AT90PWM81-16MF Atmel, AT90PWM81-16MF Datasheet - Page 262
AT90PWM81-16MF
Manufacturer Part Number
AT90PWM81-16MF
Description
IC MCU AVR 8K FLASH ISP 32QFN
Manufacturer
Atmel
Series
AVR® 90PWM Lightingr
Datasheet
1.AT90PWM81-16MN.pdf
(325 pages)
Specifications of AT90PWM81-16MF
Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
SPI
Peripherals
Brown-out Detect/Reset, PWM, WDT
Number Of I /o
20
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 11x10b; D/A 1x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Package / Case
32-MLF®, QFN
For Use With
ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOIC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT90PWM81-16MF
Manufacturer:
Atmel
Quantity:
3 118
- Current page: 262 of 325
- Download datasheet (6Mb)
21.8.2
21.8.3
262
AT90PWM81
Data Polling Flash
Data Polling EEPROM
When reading data from the AT90PWM81, data is clocked on the falling edge of SCK. See
for timing details.
To program and verify the AT90PWM81 in the serial programming mode, the following sequence is rec-
ommended (See four byte instruction formats in
When a page is being programmed into the Flash, reading an address location within the page being pro-
grammed will give the value 0xFF. At the time the device is ready for a new page, the programmed value
will read correctly. This is used to determine when the next page can be written. Note that the entire page
is written simultaneously and any address within the page can be used for polling. Data polling of the
Flash will not work for the value 0xFF, so when programming this value, the user will have to wait for at
least t
programming of addresses that are meant to contain 0xFF, can be skipped. See
value.
When a new byte has been written and is being programmed into EEPROM, reading the address location
being programmed will give the value 0xFF. At the time the device is ready for a new byte, the pro-
1.
2.
3.
4.
5.
6.
7.
8.
WD_FLASH
Power-up sequence:
Apply power between V
the programmer can not guarantee that SCK is held low during power-up. In this case, RESET
must be given a positive pulse of at least two CPU clock cycles duration after SCK has been set
to “0”.
Wait for at least 20 ms and enable serial programming by sending the Programming Enable
serial instruction to pin MOSI.
The serial programming instructions will not work if the communication is out of synchroniza-
tion. When in sync. the second byte (0x53), will echo back when issuing the third byte of the
Programming Enable instruction. Whether the echo is correct or not, all four bytes of the
instruction must be transmitted. If the 0x53 did not echo back, give RESET a positive pulse and
issue a new Programming Enable command.
The Flash is programmed one page at a time. The memory page is loaded one byte at a time by
supplying the 6 LSB of the address and data together with the Load Program Memory Page
instruction. To ensure correct loading of the page, the data low byte must be loaded before data
high byte is applied for a given address. The Program Memory Page is stored by loading the
Write Program Memory Page instruction with the 8 MSB of the address. If polling is not used,
the user must wait at least t
the serial programming interface before the Flash write operation completes can result in incor-
rect programming.
The EEPROM array is programmed one byte at a time by supplying the address and data
together with the appropriate Write instruction. An EEPROM memory location is first automat-
ically erased before new data is written. If polling is not used, the user must wait at least
t
the data file(s) need to be programmed.
Any memory location can be verified by using the Read instruction which returns the content at
the selected address at serial output MISO.
At the end of the programming session, RESET can be set high to commence normal operation.
Power-off sequence (if needed):
Set RESET to “1”.
Turn V
WD_EEPROM
CC
before programming the next page. As a chip-erased device contains 0xFF in all locations,
power off.
before issuing the next byte. (See
CC
WD_FLASH
and GND while RESET and SCK are set to “0”. In some systems,
before issuing the next page. (See
Table
Table
21-15):
21-14.) In a chip erased device, no 0xFFs in
Table
Table 21-14
21-14.) Accessing
7734P–AVR–08/10
for t
Figure 21-8
WD_FLASH
Related parts for AT90PWM81-16MF
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
IC MCU AVR 8K FLASH ISP 20SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU AVR 8K FLASH ISP 32QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU AVR 8K FLASH ISP 20SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
8-bit Avr Microcontroller With 8k Bytes In- System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: