PIC16LF1827-I/SO Microchip Technology, PIC16LF1827-I/SO Datasheet - Page 326

• Manufacturer Part Number: PIC16LF1827-I/SO
• Description: IC MCU 8BIT 4KB FLASH 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16LF1827-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 18-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• On-chip Dac: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F/LF1826/27
27.2
The Low-Voltage Programming Entry mode allows the
PIC16F/LF1826/27 devices to be programmed using
V
Configuration Word 2 is set to ‘1’, the low-voltage ICSP
programming entry is enabled. To disable the
Low-Voltage ICSP mode, the LVP bit must be
programmed to ‘0’.
Entry into the Low-Voltage Programming Entry mode
requires the following steps:
1.
2.
Once the key sequence is complete, MCLR must be
held at V
maintained.
If low-voltage programming is enabled (LVP = 1), the
MCLR Reset function is automatically enabled and
cannot be disabled. See Section 7.3 “MCLR” for more
information.
The LVP bit can only be reprogrammed to ‘0’ by using
the High-Voltage Programming mode.
27.3
Connection to a target device is typically done through
an ICSP™ header. A commonly found connector on
development tools is the RJ-11 in the 6P6C (6 pin, 6
connector) configuration. See Figure 27-2.
FIGURE 27-3:
DS41391C-page 326
DD
MCLR is brought to V
A 32-bit key sequence is presented on
ICSPDAT, while clocking ICSPCLK.
only, without high voltage. When the LVP bit of
IL
Low-Voltage Programming Entry
Mode
Common Programming Interfaces
for as long as Program/Verify mode is to be
*
PICKIT™ STYLE CONNECTOR INTERFACE
The 6-pin header (0.100" spacing) accepts 0.025" square pins.
IL
.
Preliminary
Pin 1 Indicator
1
2
3
4
5
6
FIGURE 27-2:
Another connector often found in use with the PICkit™
programmers is a standard 6-pin header with 0.1 inch
spacing. Refer to Figure 27-3.
V
PP
V
DD
/MCLR
Pin Description*
1 = V
2 = V
3 = V
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
Pin Description*
1 = V
2 = V
3 = V
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
PP
DD
SS
/MCLR
1
Target
(ground)
PP
DD
SS
2
3
/MCLR
4
(ground)
Target
5
V
6
SS
ICSPDAT
ICD RJ-11 STYLE
CONNECTOR INTERFACE
 2010 Microchip Technology Inc.
ICSPCLK
NC
Target
PC Board
Bottom Side