MC9S08QG84CDTE Freescale Semiconductor, MC9S08QG84CDTE Datasheet - Page 165

• Manufacturer Part Number: MC9S08QG84CDTE
• Description: IC MCU 8BIT 8K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG84CDTE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Controller Family/series: HCS08
• No. Of I/o's: 12
• Ram Memory Size: 512Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: DEMO9S08QG8E - BOARD DEMO FOR MC9S08QG8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

11.3.4
Freescale Semiconductor
Reset
BUSY
ARBL
RXAK
Field
IAAS
SRW
IICIF
TCF
7
6
5
4
2
1
0
W
R
IIC Status Register (IICS)
TCF
Transfer Complete Flag — This bit is set on the completion of a byte transfer. Note that this bit is only valid
during or immediately following a transfer to the IIC module or from the IIC module.The TCF bit is cleared by
reading the IICD register in receive mode or writing to the IICD in transmit mode.
0 Transfer in progress.
1 Transfer complete.
Addressed as a Slave — The IAAS bit is set when the calling address matches the programmed slave address.
Writing the IICC register clears this bit.
0 Not addressed.
1 Addressed as a slave.
Bus Busy — The BUSY bit indicates the status of the bus regardless of slave or master mode. The BUSY bit is
set when a START signal is detected and cleared when a STOP signal is detected.
0 Bus is idle.
1 Bus is busy.
Arbitration Lost — This bit is set by hardware when the arbitration procedure is lost. The ARBL bit must be
cleared by software, by writing a one to it.
0 Standard bus operation.
1 Loss of arbitration.
Slave Read/Write — When addressed as a slave the SRW bit indicates the value of the R/W command bit of
the calling address sent to the master.
0 Slave receive, master writing to slave.
1 Slave transmit, master reading from slave.
IIC Interrupt Flag — The IICIF bit is set when an interrupt is pending. This bit must be cleared by software, by
writing a one to it in the interrupt routine. One of the following events can set the IICIF bit:
0 No interrupt pending.
1 Interrupt pending.
Receive Acknowledge — When the RXAK bit is low, it indicates an acknowledge signal has been received after
the completion of one byte of data transmission on the bus. If the RXAK bit is high it means that no acknowledge
signal is detected.
0 Acknowledge received.
1 No acknowledge received.
1
7
• One byte transfer completes
• Match of slave address to calling address
• Arbitration lost
= Unimplemented or Reserved
IAAS
0
6
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
Table 11-6. IICS Register Field Descriptions
Figure 11-6. IIC Status Register (IICS)
BUSY
0
5
ARBL
0
4
Description
3
0
0
SRW
0
2
Inter-Integrated Circuit (S08IICV1)
IICIF
0
1
RXAK
0
0
163