PIC16C433-I/P Microchip Technology, PIC16C433-I/P Datasheet - Page 105

• Manufacturer Part Number: PIC16C433-I/P
• Description: IC MCU CMOS 8BIT 10MHZ 2K 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C433-I/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: LIN (Local Interconnect Network)
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• For Use With: DVA16XP185 - ADAPTER DEVICE ICE 18DIP/SOICAC164030 - MODULE SKT PROMATEII 28DIP/SOICDVA16XP140 - ADAPTER DEVICE FOR MPLAB-ICE
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

FIGURE 12-8: A/D CONVERSION TIMING
TABLE 12-12: A/D CONVERSION REQUIREMENTS
 2002 Microchip Technology Inc.
Note 1: ADRES register may be read on the following T
Param
No.
130
131
132
134
135
Note 1:
2: See Section 8.1 for minimum conditions.
*
†
§
A/D DATA
SAMPLE
A/D CLK
ADRES
These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
This specification ensured by design.
BSF ADCON0, GO
T
T
T
Sym
T
ADIF
T
SWC
ACQ
CNV
GO
AD
GO
Q4
If the A/D clock source is selected as RC, a time of T
be executed.
Characteristic
A/D clock period
Conversion time (not including S/H
time) (Note 1)
Acquisition time
Q4 to A/D clock start
Switching from convert → sample
time
134
132
(T
OSC
/2)
7
(1)
6
OLD_DATA
Preliminary
(Note 2)
5
1.5 §
CY
CY
Min
1.6
2.0
3.0
11
5*
—
SAMPLING STOPPED
is added before the A/D clock starts. This allows the SLEEP instruction to
cycle.
4
T
131
130
OSC
Typ†
4.0
6.0
20
—
—
—
—
/2 §
3
Max
6.0
9.0
2
—
11
—
—
—
—
Units
Tad
Tad
1
µs
µs
µs
µs
µs
—
T
A/D RC mode
A/D RC mode
The minimum time is the amplifier
setting time. This may be used if
the new input voltage has not
changed by more than 1 LSb (i.e.,
20.0 mV @ 5.12V) from the last
sampled voltage (as stated on
C
If the A/D clock source is selected
as RC, a time of T
before the A/D clock starts. This
allows the SLEEP instruction to be
executed.
1 T
0
OSC
HOLD
PIC16C433
CY
based, V
).
NEW_DATA
DONE
Conditions
DS41139B-page 103
REF
CY
≥ 2.5V
is added