PIC16F785-I/SO Microchip Technology, PIC16F785-I/SO Datasheet - Page 47

• Manufacturer Part Number: PIC16F785-I/SO
• Description: IC PIC MCU FLASH 2KX14 20SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F785-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 20-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: RS- 232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164120, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SO1-1 - SOCKET TRANS ICE 20DIP TO 20SOICXLT18SO-1 - SOCKET TRANSITION 18SOIC 300MILAC162060 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOIC
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.4
PORTC is an 8-bit wide, bidirectional port. The corre-
sponding data direction register is TRISC (Register 4-
8). Setting a TRISC bit (= 1) will make the correspond-
ing PORTC pin an input (i.e., put the corresponding
output driver in a High-Impedance mode). Clearing a
TRISC bit (= 0) will make the corresponding PORTC
pin an output (i.e., put the contents of the output latch
on the selected pin). Example 4-3 shows how to initial-
ize PORTC.
Reading the PORTC register (Register 4-7) reads the
status of the pins, whereas writing to it will write to the
port latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then
written to the port data latch.
The TRISC register controls the direction of the
PORTC pins, even when they are being used as
analog inputs. The user must ensure the bits in the
TRISC register are maintained set when using them as
analog inputs. I/O pins configured as analog input
always read ‘0’.
REGISTER 4-7:
REGISTER 4-8:
© 2008 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-0
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-0
Note 1: Data latches are unknown after a POR, but each port bit reads ‘0’ when the corresponding analog select bit
R/W-x
TRISC7
R/W-1
RC7
PORTC and TRISC Registers
(1)
is ‘1’ (see Registers
RC<7:0>: PORTC General Purpose I/O Pin bits
1 = Port pin is greater than V
0 = Port pin is less than V
TRISC<7:0>: PORTC Tri-State Control bits
1 = PORTC pin configured as an input (tri-stated)
0 = PORTC pin configured as an output
R/W-x
TRISC6
R/W-1
RC6
PORTC: PORTC REGISTER
TRISC: PORTC TRI-STATE REGISTER
(1)
W = Writable bit
‘1’ = Bit is set
W = Writable bit
‘1’ = Bit is set
12-1
TRISC5
R/W-1
R/W-x
RC5
and
12-2 on page 82
IL
IH
TRISC4
R/W-1
R/W-x
RC4
).
U = Unimplemented bit, read as ‘0’
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
‘0’ = Bit is cleared
R/W-x
TRISC3
R/W-1
When RC4 or RC5 is configured as an op amp output,
the corresponding RC4 or RC5 digital output driver will
automatically be disabled regardless of the TRISC<4>
or TRISC<5> value.
EXAMPLE 4-3:
RC3
BCF
BCF
CLRF
BSF
CLRF
CLRF
MOVLW
MOVWF
BCF
Note:
(1)
PIC16F785/HV785
STATUS,RP0
STATUS,RP1
PORTC
STATUS,RP0
ANSEL0
ANSEL1
0Ch
TRISC
STATUS,RP0
The ANSEL0 (91h) and ANSEL1 (93h)
registers must be initialized to configure
an analog channel as a digital input. Pins
configured as analog inputs will read ‘0’.
R/W-x
TRISC2
R/W-1
RC2
(1)
INITIALIZING PORTC
x = Bit is unknown
x = Bit is unknown
;Bank 0
;Init PORTC
;Bank 1
;digital I/O
;digital I/O
;Set RC<3:2> as inputs
; and set RC<5:4,1:0>
; as outputs
;Bank 0
R/W-x
TRISC1
R/W-1
RC1
(1)
DS41249E-page 45
R/W-x
TRISC0
R/W-1
RC0
(1)
bit 0
bit 0