SAK-XC164CM-4F40F AA Infineon Technologies, SAK-XC164CM-4F40F AA Datasheet - Page 63
![IC MCU 16BIT 32KB FLSH TQFP-64-8](/photos/12/23/122341/sak-xc164cm-4f40f_aa_sml.jpg)
SAK-XC164CM-4F40F AA
Manufacturer Part Number
SAK-XC164CM-4F40F AA
Description
IC MCU 16BIT 32KB FLSH TQFP-64-8
Manufacturer
Infineon Technologies
Series
XC16xr
Datasheet
1.SAF-XC164CM-4F20F_AA.pdf
(70 pages)
Specifications of SAK-XC164CM-4F40F AA
Core Processor
C166SV2
Core Size
16-Bit
Speed
40MHz
Connectivity
CAN, SPI, UART/USART
Peripherals
PWM, WDT
Number Of I /o
47
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2.35 V ~ 2.7 V
Data Converters
A/D 14x8/10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
64-LFQFP
For Use With
B158-H8961-X-X-7600IN - KIT EASY XC164CMXC164CMUCANIN - KIT U-CAN STARTER XC164CMMCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
SAK-XC164CM-4F40FAACT
SAK-XC164CM-4F40FAACT
SAK-XC164CM-4F40FAAINCT
SAK-XC164CM-4F40FAACT
SAK-XC164CM-4F40FAAINCT
This is especially important for bus cycles using waitstates and e.g. for the operation of
timers, serial interfaces, etc. For all slower operations and longer periods (e.g. pulse train
generation or measurement, lower baudrates, etc.) the deviation caused by the PLL jitter
is negligible.
The value of the accumulated PLL jitter depends on the number of consecutive VCO
output cycles within the respective timeframe. The VCO output clock is divided by the
output prescaler (K = PLLODIV+1) to generate the master clock signal
the number of VCO cycles can be represented as K × N, where N is the number of
consecutive
For a period of N × TCM the accumulated PLL jitter is defined by the deviation D
D
So, for a period of 3 TCMs @ 20 MHz and K = 12: D
This formula is applicable for K × N < 95. For longer periods the K × N = 95 value can be
used. This steady value can be approximated by: D
Figure 16
Note: The bold lines indicate the minimum accumulated jitter which can be achieved by
Data Sheet
N
[ns] = ±(1.5 + 6.32 × N /
selecting the maximum possible output prescaler factor K.
Acc. jitter
±8
±7
±6
±5
±4
±3
±2
±1
ns
f
0
MC
Approximated Accumulated PLL Jitter
0
cycles (TCM).
1
10 MHz
40 MHz
D
N
K = 15
5
20 MHz
f
MC
K = 12
);
f
MC
K = 10
10
in [MHz], N = number of consecutive TCMs.
K = 8
61
K = 6 K = 5
15
3
Nmax
= ±(1.5 + 6.32 × 3 / 20) = 2.448 ns.
[ns] = ±(1.5 + 600 / (K ×
20
Electrical Parameters
25
MCD05566
f
MC
Derivatives
V1.4, 2007-03
. Therefore,
XC164CM
N
N
f
MC
:
)).