SAK-XC2786X-96F66L AC Infineon Technologies, SAK-XC2786X-96F66L AC Datasheet - Page 81
![IC MCU 16BIT FLASH PG-LQFP-144](/photos/12/23/122314/sak-xc2786x-96f66l_ac_sml.jpg)
SAK-XC2786X-96F66L AC
Manufacturer Part Number
SAK-XC2786X-96F66L AC
Description
IC MCU 16BIT FLASH PG-LQFP-144
Manufacturer
Infineon Technologies
Series
XC27x6Xr
Datasheet
1.SAK-XC2786X-96F66L_AC.pdf
(120 pages)
Specifications of SAK-XC2786X-96F66L AC
Core Processor
C166SV2
Core Size
16/32-Bit
Speed
66MHz
Connectivity
CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
Peripherals
I²S, POR, PWM, WDT
Number Of I /o
116
Program Memory Size
768KB (768K x 8)
Program Memory Type
FLASH
Ram Size
51K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 24x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
144-LFQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
KX2786X96F66LACXT
SAK-XC2786X-96F66LACINTR
SP000369364
SAK-XC2786X-96F66LACINTR
SP000369364
2) Not subject to production test - verified by design/characterization. Hysteresis is implemented to avoid
3) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
4) As a rule, with decreasing output current the output levels approach the respective supply level (
5) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
6) An additional error current (
7) The given values are worst-case values. In production test, this leakage current is only tested at 125°C; other
8) Keep current: Limit the current through this pin to the indicated value so that the enabled pull device can keep
9) Not subject to production test - verified by design/characterization.
Data Sheet
metastable states and switching due to internal ground bounce. It cannot suppress switching due to external
system noise under all conditions.
Table
V
output will float and the voltage is determined by the external circuit.
the definition of the overload coupling factor
The leakage current value is not tested in the lower voltage range but only in the upper voltage range. This
parameter is ensured by correlation.
values are ensured by correlation. For derating, please refer to the following descriptions:
Leakage derating depending on temperature (
I
4.41 µA.
Leakage derating depending on voltage level (DV =
I
This voltage derating formula is an approximation which applies for maximum temperature.
Because pin P2.8 is connected to two pads (standard pad and high-speed clock pad), it has twice the normal
leakage.
the default pin level:
Force current: Drive the indicated minimum current through this pin to change the default pin level driven by
the enabled pull device:
These values apply to the fixed pull-devices in dedicated pins and to the user-selectable pull-devices in
general purpose IO pins.
Because pin P2.8 is connected to two pads (standard pad and high-speed clock pad), it has twice the normal
capacitance.
OZ
OZ
OH
=
→
= 0.03 × e
I
V
OZtempmax
13,
DDP
Current Limits for Port Output
). However, only the levels for nominal output currents are verified.
(1.35 + 0.028×TJ)
- (1.3 × DV) [µA]
V
PIN
V
≥
PIN
V
I
[µA]. For example, at a temperature of 130°C the resulting leakage current is
INJ
IH
≤
) will flow if an overload current flows through an adjacent pin. Please refer to
for a pullup;
V
IL
for a pullup;
Drivers. The limit for pin groups must be respected.
V
K
PIN
OV
T
V
J
≤
.
PIN
= junction temperature [°C]):
V
79
IL
≥
V
for a pulldown.
V
DDP
IH
for a pulldown.
-
V
PIN
[V]):
XC2000 Family Derivatives
Electrical Parameters
V2.1, 2008-08
XC2786X
V
OL
→
V
SS
,