C8051F346-GQ Silicon Laboratories Inc, C8051F346-GQ Datasheet - Page 97
![IC 8051 MCU FLASH 64K 32LQFP](/photos/12/18/121867/c8051f346-gq_sml.jpg)
C8051F346-GQ
Manufacturer Part Number
C8051F346-GQ
Description
IC 8051 MCU FLASH 64K 32LQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F34xr
Datasheets
1.C8051F349-GQ.pdf
(276 pages)
2.C8051F346-GQ.pdf
(1 pages)
3.C8051F347-GQ.pdf
(296 pages)
Specifications of C8051F346-GQ
Program Memory Type
FLASH
Program Memory Size
64KB (64K x 8)
Package / Case
32-LQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
25
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 21x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F3x
Core
8051
Data Bus Width
8 bit
Data Ram Size
5.25 KB
Interface Type
I2C/SMBus/SPI/UART/USB
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
25
Number Of Timers
4
Operating Supply Voltage
2.7 V to 5.25 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F340DK
Minimum Operating Temperature
- 40 C
On-chip Adc
17-ch x 10-bit
No. Of I/o's
25
Ram Memory Size
4352Byte
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1748 - ADAPTER TOOLSTICK FOR C8051F34X770-1006 - ISP 4PORT FOR SILABS C8051F MCU
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1304
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F346-GQ
Manufacturer:
SiliconL
Quantity:
578
Company:
Part Number:
C8051F346-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F346-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
9.4.
Power Management Modes
The CIP-51 core has two software programmable power management modes: Idle and Stop. Idle mode
halts the CPU while leaving the peripherals and clocks active. In Stop mode, the CPU is halted, all inter-
rupts, are inactive, and the internal oscillator is stopped (analog peripherals remain in their selected states;
the external oscillator is not affected). Since clocks are running in Idle mode, power consumption is depen-
dent upon the system clock frequency and the number of peripherals left in active mode before entering
Idle. Stop mode consumes the least power. Figure 1.15 describes the Power Control Register (PCON)
used to control the CIP-51's power management modes.
Although the CIP-51 has Idle and Stop modes built in (as with any standard 8051 architecture), power
management of the entire MCU is better accomplished through system clock and individual peripheral
management. Each analog peripheral can be disabled when not in use and placed in low power mode.
Digital peripherals, such as timers or serial buses, draw little power when they are not in use. Turning off
the oscillators lowers power consumption considerably; however a reset is required to restart the MCU.
The internal oscillator can be placed in Suspend mode (see
Section “14. Oscillators” on page
131). In
Suspend mode, the internal oscillator is stopped until a non-idle USB event is detected, or the VBUS input
signal matches the polarity selected by the VBPOL bit in register REG0CN (SFR Definition 8.1).
9.4.1. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the CIP-51 to halt the CPU and enter Idle mode as soon
as the instruction that sets the bit completes execution. All internal registers and memory maintain their
original data. All analog and digital peripherals can remain active during Idle mode.
Idle mode is terminated when an enabled interrupt is asserted or a reset occurs. The assertion of an
enabled interrupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU to resume
operation. The pending interrupt will be serviced and the next instruction to be executed after the return
from interrupt (RETI) will be the instruction immediately following the one that set the Idle Mode Select bit.
If Idle mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence
and begins program execution at address 0x0000.
If enabled, the Watchdog Timer (WDT) will eventually cause an internal watchdog reset and thereby termi-
nate the Idle mode. This feature protects the system from an unintended permanent shutdown in the event
of an inadvertent write to the PCON register. If this behavior is not desired, the WDT may be disabled by
software prior to entering the Idle mode if the WDT was initially configured to allow this operation. This pro-
vides the opportunity for additional power savings, allowing the system to remain in the Idle mode indefi-
nitely, waiting for an external stimulus to wake up the system. Refer to
Section “11.6. PCA Watchdog
Timer Reset” on page 103
for more information on the use and configuration of the WDT.
9.4.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the CIP-51 to enter Stop mode as soon as the instruc-
tion that sets the bit completes execution. In Stop mode the internal oscillator, CPU, and all digital peripher-
als are stopped; the state of the external oscillator circuit is not affected. Each analog peripheral (including
the external oscillator circuit) may be shut down individually prior to entering Stop Mode. Stop mode can
only be terminated by an internal or external reset. On reset, the CIP-51 performs the normal reset
sequence and begins program execution at address 0x0000.
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode.
The Missing Clock Detector should be disabled if the CPU is to be put to in STOP mode for longer than the
MCD timeout of 100 µsec.
Rev. 1.3
97