MCF52213CAE50 Freescale Semiconductor, MCF52213CAE50 Datasheet - Page 21

• Manufacturer Part Number: MCF52213CAE50
• Description: IC MCU 32BIT 128K FLASH 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF5221xr

Specifications of MCF52213CAE50

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SPI, UART/USART, USB OTG
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: MCF522x
• Core: ColdFire V2
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, QSPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 43
• Number Of Timers: 18
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: M52210DEMO, M52211EVB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 8 Channel
• A/d Bit Size: 12 bit
• A/d Channels Available: 8
• Height: 1.4 mm
• Length: 10 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Width: 10 mm
• For Use With: M52210DEMO - BOARD DEV MCF5221X LOW COST
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

1.3
Table 4
1.4
Table 5
1.5
Table 6
Freescale Semiconductor
Clock Mode Selection
Reset Configuration
describes signals used to reset the chip or as a reset indication.
describes signals used to support the on-chip clock generation circuitry.
describes signals used in mode selection;
External Clock In
Signal Name
Signal Name
Signal Name
Reset Out
Reset Signals
PLL and Clock Signals
Mode Selection
Clock Out
Reset In
Crystal
Test
CLKMOD[1:0]
00
00
Abbreviation
Abbreviation
CLKMOD[1:0] Selects the clock boot mode.
Abbreviation
CLKOUT
RSTO
EXTAL
RSTI
XTAL
RCON
XTAL
TEST
0
1
MCF52211 ColdFire Microcontroller, Rev. 2
Table 6. Mode Selection Signals
Primary reset input to the device. Asserting RSTI for at least 8 CPU
clock cycles immediately resets the CPU and peripherals.
Driven low for 1024 CPU clocks after the reset source has deasserted.
Table 5. PLL and Clock Signals
PLL disabled, clock driven by external oscillator
PLL disabled, clock driven by on-chip oscillator
Crystal oscillator or external clock input except when the on-chip
relaxation oscillator is used.
Crystal oscillator output except when CLKMOD0=0, then sampled as
part of the clock mode selection mechanism.
This output signal reflects the internal system clock.
The Serial Flash Programming mode is entered by asserting the
RCON pin (with the TEST pin negated) as the chip comes out of
reset. During this mode, the EzPort has access to the flash memory
which can be programmed from an external device.
Reserved for factory testing only and in normal modes of operation
should be connected to VSS to prevent unintentional activation of
test functions.
Table 7. Clocking Modes
Table 7
Table 4. Reset Signals
describes the particular clocking modes.
Configure the clock mode.
Function
Function
Function
Family Configurations
I/O
I/O
I/O
O
O
O
I
I
I
I
21