MC9S08QG8CDTE Freescale Semiconductor, MC9S08QG8CDTE Datasheet - Page 133

• Manufacturer Part Number: MC9S08QG8CDTE
• Description: IC MCU 8K FLASH 10MHZ 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG8CDTE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 512Byte
• # I/os (max): 12
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• Package: 16TSSOP
• Family Name: HCS08
• Maximum Speed: 20 MHz
• For Use With: DEMO9S08QG8E - BOARD DEMO FOR MC9S08QG8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

are too fast, then the clock must be divided to the appropriate frequency. This divider is specified by the
ADIV bits and can be divide-by 1, 2, 4, or 8.
9.4.2
The pin control registers (APCTL3, APCTL2, and APCTL1) are used to disable the I/O port control of the
pins used as analog inputs.When a pin control register bit is set, the following conditions are forced for the
associated MCU pin:
9.4.3
The ADC module has a selectable asynchronous hardware conversion trigger, ADHWT, that is enabled
when the ADTRG bit is set. This source is not available on all MCUs. Consult the module introduction for
information on the ADHWT source specific to this MCU.
When ADHWT source is available and hardware trigger is enabled (ADTRG=1), a conversion is initiated
on the rising edge of ADHWT. If a conversion is in progress when a rising edge occurs, the rising edge is
ignored. In continuous convert configuration, only the initial rising edge to launch continuous conversions
is observed. The hardware trigger function operates in conjunction with any of the conversion modes and
configurations.
9.4.4
Conversions can be performed in either 10-bit mode or 8-bit mode as determined by the MODE bits.
Conversions can be initiated by either a software or hardware trigger. In addition, the ADC module can be
configured for low power operation, long sample time, continuous conversion, and automatic compare of
the conversion result to a software determined compare value.
9.4.4.1
A conversion is initiated:
If continuous conversions are enabled a new conversion is automatically initiated after the completion of
the current conversion. In software triggered operation, continuous conversions begin after ADCSC1 is
written and continue until aborted. In hardware triggered operation, continuous conversions begin after a
hardware trigger event and continue until aborted.
Freescale Semiconductor
•
•
•
•
•
•
The output buffer is forced to its high impedance state.
The input buffer is disabled. A read of the I/O port returns a zero for any pin with its input buffer
disabled.
The pullup is disabled.
Following a write to ADCSC1 (with ADCH bits not all 1s) if software triggered operation is
selected.
Following a hardware trigger (ADHWT) event if hardware triggered operation is selected.
Following the transfer of the result to the data registers when continuous conversion is enabled.
Input Select and Pin Control
Hardware Trigger
Conversion Control
Initiating Conversions
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
Analog-to-Digital Converter (S08ADC10V1)
131