C8051T606-ZM Silicon Laboratories Inc, C8051T606-ZM Datasheet - Page 57
![IC 8051 MCU 1.5K-EEPROM 10-QFN](/photos/12/15/121567/10-qfn_pkg_sml.jpg)
C8051T606-ZM
Manufacturer Part Number
C8051T606-ZM
Description
IC 8051 MCU 1.5K-EEPROM 10-QFN
Manufacturer
Silicon Laboratories Inc
Series
C8051T60xr
Specifications of C8051T606-ZM
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1.5KB (1.5K x 8)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
10-QFN
Processor Series
C8051T6x
Core
8051
Data Bus Width
8 bit
Data Ram Size
128 B
Interface Type
I2C, UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
6
Number Of Timers
3
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051T606DK
Minimum Operating Temperature
- 40 C
Eeprom Size
-
Data Converters
-
For Use With
336-1668 - CARD DAUGHTER QFN10 SOCKET336-1667 - CARD DAUGHTER MSOP SOCKET336-1666 - KIT DEVELOPMENT FOR C8051T606336-1404 - KIT DEV FOR C8051T60X MCU'S
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Details
Other names
336-1663-2
C8051T606-ZMR
C8051T606-ZMR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051T606-ZMR
Manufacturer:
STM
Quantity:
4 037
C8051T600/1/2/3/4/5/6
12. Voltage Regulator (REG0)
C8051T600/1/2/3/4/5/6 devices include an internal voltage regulator (REG0) to regulate the internal core
supply to 1.8 V from a V
supply of 1.8 to 3.6 V. Two power-saving modes are built into the regulator to
DD
help reduce current consumption in low-power applications. These modes are accessed through the
REG0CN register (SFR Definition 12.1). Electrical characteristics for the on-chip regulator are specified in
Table 8.5 on page 34.
If an external regulator is used to power the device, the internal regulator may be put into bypass mode
using the BYPASS bit. The internal regulator should never be placed in bypass mode unless an
external 1.8 V regulator is used to supply V
. Doing so could cause permanent damage to the
DD
device.
Under default conditions, when the device enters STOP mode the internal regulator will remain on. This
allows any enabled reset source to generate a reset for the device and bring the device out of STOP mode.
For additional power savings, the STOPCF bit can be used to shut down the regulator and the internal
power network of the device when the part enters STOP mode. When STOPCF is set to 1, the RST pin or
a full power cycle of the device are the only methods of generating a reset.
Rev. 1.2
57