STM32F103T4U6A STMicroelectronics, STM32F103T4U6A Datasheet - Page 41

• Manufacturer Part Number: STM32F103T4U6A
• Description: MCU ARM 32BIT 16K FLASH 36VFQFPN
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103T4U6A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 36-VFQFN, 36-VFQFPN
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8318

STM32F103x4, STM32F103x6
Figure 18. Typical current consumption in Standby mode versus temperature at
V
Typical current consumption
The MCU is placed under the following conditions:
●
●
●
●
●
●
4.5
3.5
2.5
1.5
0.5
DD
4
3
2
1
0
= 3.3 V and 3.6 V
All I/O pins are in input mode with a static value at V
All peripherals are disabled except if it is explicitly mentioned.
The
wait state from 24 to 48 MHz and 2 wait states above).
Ambient temperature and V
Prefetch is ON (Reminder: this bit must be set before clock setting and bus prescaling)
When the peripherals are enabled f
f
PCLK2
Flash
–45 °C
/4
access time is adjusted to f
25 °C
Doc ID 15060 Rev 5
Temperature (°C)
DD
supply voltage conditions summarized in
PCLK1
HCLK
85 °C
= f
frequency (0 wait state from 0 to 24 MHz, 1
HCLK
/4, f
DD
PCLK
105 °C
or V
2 = f
SS
Electrical characteristics
HCLK
(no load).
/2, f
ADCCLK
3.3 V
3.6 V
Table
9.
=
41/87