DSPIC30F6014-20I/PF Microchip Technology, DSPIC30F6014-20I/PF Datasheet - Page 3

• Manufacturer Part Number: DSPIC30F6014-20I/PF
• Description: IC DSPIC MCU/DSP 144K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F6014-20I/PF

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 144KB (48K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 68
• Flash Memory Size: 144KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 80TQFP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 68
• Interface Type: 3-Wire/AC97/CAN/I2C/I2S/SPI/UART
• On-chip Adc: 16-chx12-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1DM300004-2 - BOARD DEMO DSPICDEM.NET 2DM300004-1 - BOARD DEMO DSPICDEM.NET 1AC164314 - MODULE SKT FOR PM3 80PFAC30F001 - MODULE SOCKET DSPIC30F 80TQFPXLT80PT2 - SOCKET TRANSITION ICE 80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F601420IPF

1. Module: Data EEPROM – Speed
2. Module: CPU – Unsigned
© 2008 Microchip Technology Inc.
At device throughput greater than 20 MIPS for
V
V
instructions (TBLRDL/TBLRDH) and instructions
that use Program Space Visibility (PSV) do not
function correctly when reading data from data
EEPROM.
Work around
When reading data from data EEPROM, the
application should
operation to lower the frequency of the system
clock so that the throughput is less than 20 MIPS.
This may be easily performed at any time via the
Oscillator
(OSCCON<7:6>), that allow the application to
divide the system clock down by a factor of 4, 16
or 64.
The US (CORCON<12>) bit controls whether MAC
type DSP instructions operate in Signed or
Unsigned mode. The device defaults to a Signed
mode on power-up (US = 0).
For this revision of silicon, MAC type DSP
instructions do not function as specified in
Unsigned mode (US = 1). Also, for this revision,
the US bit will always read as ‘0’.
Work around
Ensure that the US bit is not set by the application.
In
multiplications, use the MCU Multiply instruction,
MUL.UU.
DD
DD
, in the range 4.75V to 5.5V (or 10 MIPS for
order
in the range 3V to 3.6V), table read
to
Postscaler
perform
perform a
bits,
unsigned
MAC
dsPIC30F6011/6012/6013/6014
clock switch
POST<1:0>
integer
3. Module: MAC class Instructions with +4
4. Module: CPU –
EXAMPLE 1:
L0:daw.b
L1: ....
Sequential MAC class instructions, which prefetch
data from Y data space using +4 address
modification, will cause an address error trap. The
trap occurs only when all of the following
conditions are true:
1. Two sequential MAC class instructions (or a
2. Both instructions prefetch data from Y data
3. Neither of the instruction uses an accumulator
Work around
The problem described above can be avoided by
using any of the following methods:
1. Inserting any other instruction between the two
2. Adding an accumulator write back (a dummy
3. Do not use the + = 4 or - = 4 address
4. Do not prefetch data from Y data space.
The Decimal Adjust instruction, DAW.b, may
improperly clear the Carry bit, C (SR<0>), when
executed.
Work around
Check the state of the Carry bit prior to executing
the DAW.b instruction. If the Carry bit is set, set the
Carry bit again after executing the DAW.b
instruction. Example 1 shows how the application
should process the Carry bit during a BCD addition
operation.
.include “p30fxxxx.inc”
.......
mov.b
mov.b
add.b
bra
daw.b
bset.b
bra
MAC class instruction executed in a REPEAT or
DO loop) that prefetch from Y data space.
space using the + = 4 or - = 4 address
modification.
write back.
MAC class instructions.
write back if needed) to either of the MAC class
instructions.
modification.
#0x80, w0
#0x80, w1
w0, w1, w2 ;Perform addition
NC, L0
w2
L1
w2
SR, #C
Address Modification
CHECK CARRY BIT BEFORE
DAW.b
DAW.b
;First BCD number
;Second BCD number
;If C set go to L0
;If not,do DAW and
;set the carry bit
;and exit
Instruction
DS80198J-page 3