PIC16C74A-20/P Microchip Technology, PIC16C74A-20/P Datasheet - Page 124

• Manufacturer Part Number: PIC16C74A-20/P
• Description: IC MCU OTP 4KX14 A/D PWM 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C74A-20/P

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 8x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 33
• Ram Memory Size: 192Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 33
• Interface Type: I2C/SPI/USART
• On-chip Adc: 8-chx8-bit
• Number Of Timers: 3
• Core: PIC
• Processor Series: PIC16C
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 192 B
• Data Rom Size: 192 B
• Mounting Style: Through Hole
• A/d Bit Size: 8 bit
• A/d Channels Available: 8
• Height: 3.81 mm
• Length: 52.26 mm
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Supply Voltage (max): 6 V
• Supply Voltage (min): 4 V
• Width: 13.84 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC16C63A/65B/73B/74B
16.2.3
FIGURE 16-5:
TABLE 16-2:
DS30605C-page 124
Note 1: Instruction cycle period (T
Param
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and
No.
1A
3*
4*
1
2
are not tested.
CLKOUT
OSC1
based on characterization data for that particular oscillator type under standard operating conditions with the
device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption. All devices are tested to operate at “min.” values with an external
clock applied to the OSC1/CLKIN pin. When an external clock input is used, the “Max.” cycle time limit is
“DC” (no clock) for all devices.
TosR,
F
TosL,
T
TosH
Sym
TosF
TIMING DIAGRAMS AND SPECIFICATIONS
T
OSC
OSC
CY
EXTERNAL CLOCK TIMING REQUIREMENTS
External CLKIN Frequency
(Note 1)
Oscillator Frequency
(Note 1)
External CLKIN Period
(Note 1)
Oscillator Period
(Note 1)
Instruction Cycle Time (Note 1)
External Clock in (OSC1) High or
Low Time
External Clock in (OSC1) Rise or
Fall Time
EXTERNAL CLOCK TIMING
Q4
Characteristic
CY
) equals four times the input oscillator time-base period. All specified values are
Q1
1
Min
250
250
250
250
250
200
100
DC
DC
DC
DC
DC
0.1
2.5
50
50
15
—
—
—
4
5
5
5
Q2
Typ†
2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
3
Q3
10,000
Max
200
200
250
250
DC
20
20
25
50
15
—
—
—
—
—
—
—
—
—
4
4
4
4
3
Units
MHz RC and XT osc modes
MHz HS osc mode (-04)
MHz HS osc mode (-20)
MHz RC osc mode
MHz XT osc mode
MHz HS osc mode
kHz
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
s
s
s
Q4
4
LP osc mode
LP osc mode
RC and XT osc modes
HS osc mode (-04)
HS osc mode (-20)
LP osc mode
RC osc mode
XT osc mode
HS osc mode (-04)
HS osc mode (-20)
LP osc mode
T
XT oscillator
LP oscillator
HS oscillator
XT oscillator
LP oscillator
HS oscillator
CY
2000 Microchip Technology Inc.
= 4/F
4
OSC
Conditions
Q1