PIC16LF876-04I/SO Microchip Technology, PIC16LF876-04I/SO Datasheet - Page 88

• Manufacturer Part Number: PIC16LF876-04I/SO
• Description: IC MCU FLASH 8KX14 EE A/D 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16LF876-04I/SO

• Core Size: 8-Bit
• Program Memory Size: 14KB (8K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC16LF
• No. Of I/o's: 22
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 368Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• Processor Series: PIC16LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: MSSP, PSP, USART
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 1
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 5 Channel
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 4 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F87X
9.2.13
An Acknowledge sequence is enabled by setting the
Acknowledge
(SSPCON2<4>). When this bit is set, the SCL pin is
pulled low and the contents of the Acknowledge data bit
is presented on the SDA pin. If the user wishes to gen-
erate an Acknowledge, the ACKDT bit should be
cleared. If not, the user should set the ACKDT bit
before starting an Acknowledge sequence. The baud
rate generator then counts for one rollover period
(T
SCL pin is sampled high (clock arbitration), the baud
FIGURE 9-16:
DS30292C-page 86
BRG
), and the SCL pin is de-asserted high. When the
Note: T
ACKNOWLEDGE SEQUENCE
TIMING
BRG
SSPIF
Sequence
Acknowledge sequence starts here,
SDA
SCL
= one baud rate generator period.
ACKNOWLEDGE SEQUENCE WAVEFORM
Set SSPIF at the end
of receive
ACKEN = 1, ACKDT = 0
Enable
Write to SSPCON2
bit,
8
D0
ACKEN
Cleared in
software
T
BRG
ACK
rate generator counts for T
pulled low. Following this, the ACKEN bit is automati-
cally cleared, the baud rate generator is turned off,
and the SSP module then goes into IDLE mode
(Figure 9-16).
9.2.13.1
If the user writes the SSPBUF when an Acknowledge
sequence is in progress, the WCOL is set and the con-
tents of the buffer are unchanged (the write doesn’t
occur).
T
BRG
9
Set SSPIF at the end
of Acknowledge sequence
ACKEN automatically cleared
WCOL Status Flag
Cleared in
software
2001 Microchip Technology Inc.
BRG
. The SCL pin is then