PIC16LF876-04I/SO Microchip Technology, PIC16LF876-04I/SO Datasheet - Page 103

• Manufacturer Part Number: PIC16LF876-04I/SO
• Description: IC MCU FLASH 8KX14 EE A/D 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16LF876-04I/SO

• Core Size: 8-Bit
• Program Memory Size: 14KB (8K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC16LF
• No. Of I/o's: 22
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 368Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• Processor Series: PIC16LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: MSSP, PSP, USART
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 1
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 5 Channel
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 4 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

10.2.2
The receiver block diagram is shown in Figure 10-4.
The data is received on the RC7/RX/DT pin and drives
the data recovery block. The data recovery block is
actually a high speed shifter, operating at x16 times the
baud rate; whereas, the main receive serial shifter
operates at the bit rate or at F
Once Asynchronous mode is selected, reception is
enabled by setting bit CREN (RCSTA<4>).
The heart of the receiver is the receive (serial) shift reg-
ister (RSR). After sampling the STOP bit, the received
data in the RSR is transferred to the RCREG register (if
it is empty). If the transfer is complete, flag bit RCIF
(PIR1<5>) is set. The actual interrupt can be enabled/
disabled
(PIE1<5>). Flag bit RCIF is a read only bit, which is
cleared by the hardware. It is cleared when the RCREG
register has been read and is empty. The RCREG is a
double buffered register (i.e., it is a two deep FIFO). It
FIGURE 10-4:
2001 Microchip Technology Inc.
by
F
USART ASYNCHRONOUS
RECEIVER
RC7/RX/DT
OSC
setting/clearing
Baud Rate Generator
x64 Baud Rate CLK
USART RECEIVE BLOCK DIAGRAM
SPBRG
Pin Buffer
and Control
SPEN
OSC
.
enable
bit
Data
Recovery
Interrupt
RCIE
or
64
16
CREN
is possible for two bytes of data to be received and
transferred to the RCREG FIFO and a third byte to
begin shifting to the RSR register. On the detection of
the STOP bit of the third byte, if the RCREG register is
still full, the overrun error bit OERR (RCSTA<1>) will be
set. The word in the RSR will be lost. The RCREG reg-
ister can be read twice to retrieve the two bytes in the
FIFO. Overrun bit OERR has to be cleared in software.
This is done by resetting the receive logic (CREN is
cleared and then set). If bit OERR is set, transfers from
the RSR register to the RCREG register are inhibited,
and no further data will be received. It is therefore,
essential to clear error bit OERR if it is set. Framing
error bit FERR (RCSTA<2>) is set if a STOP bit is
detected as clear. Bit FERR and the 9th receive bit are
buffered the same way as the receive data. Reading
the RCREG will load bits RX9D and FERR with new
values, therefore, it is essential for the user to read the
RCSTA register before reading the RCREG register in
order not to lose the old FERR and RX9D information.
RCIF
RCIE
RX9
MSb
STOP
RX9D
(8) 7
OERR
RCREG Register
RSR Register
8
Data Bus
PIC16F87X
1
FERR
0
START
DS30292C-page 101
FIFO
LSb