DSPIC30F4013-20I/PT Microchip Technology, DSPIC30F4013-20I/PT Datasheet - Page 5

• Manufacturer Part Number: DSPIC30F4013-20I/PT
• Description: IC DSPIC MCU/DSP 48K 44TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F4013-20I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, POR, PWM, WDT
• Number Of I /o: 30
• Program Memory Size: 48KB (16K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 30
• Flash Memory Size: 48KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 44TQFP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 30
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 13-chx12-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPAC30F006 - MODULE SKT FOR DSPIC30F 44TQFPAC164305 - MODULE SKT FOR PM3 44TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F401320IPT

4. Module: Interrupt Controller – Sequential
© 2008 Microchip Technology Inc.
When interrupt nesting is enabled (or NSTDIS
(INTCON1<15>) bit is ‘0’) the following sequence
of events will lead to an address error trap. The
generic terms “Interrupt 1” and “Interrupt 2” are
used to represent any two enabled dsPIC30F
interrupts.
1. Interrupt 1 processing begins.
2. Interrupt 1 is negated by user software by one
3. Interrupt 2 occurs with a priority higher than
EXAMPLE 4: USING DISI
EXAMPLE 5: RAISING CPU INTERRUPT PRIORITY LEVEL
EXAMPLE 6: USING MACRO
.include
...
DISI#2 ; protect the disable of INT1
BCLRIEC1, #INT1IE; disable interrupt 1
...
.include
...
__asm__ volatile (“DISI #0x1FFF”);
SRbits.IPL = 0x5;
DISICNT = 0x0;
#define DISI_PROTECT(X) {\
DISI_PROTECT(SRbits.IPL = 0x5);
of the following methods:
- CPU IPL is raised to Interrupt 1 IPL level or
- Interrupt 1 IPL is lowered to CPU IPL level or
- Interrupt 1 is disabled (Interrupt 1 IE bit set to
- Interrupt 1 flag is cleared
Interrupt 1.
higher or
lower or
‘0’) or
__asm__ volatile (“DISI #0x1FFF”);\
X;
DISICNT = 0; }
; next instruction protected by DISI
Interrupts
“p30fxxxx.inc”
“p30fxxxx.h”
\
// safely modify the CPU IPL
// protect CPU IPL modification
// set CPU IPL to 5
// remove DISI protection
dsPIC30F3014/4013
Work around
The user may disable interrupt nesting or execute
a DISI instruction before modifying the CPU IPL
or Interrupt 1 setting. A minimum DISI value of 2
is required if the DISI is executed immediately
before the CPU IPL or Interrupt 1 is modified, as
shown in Example 4. If the MPLAB C30 compiler
is being used, one must inspect the Disassembly
Listing in the MPLAB IDE file to determine the
exact number of cycles to disable level 1-6
interrupts. One may use a large DISI value and
then set the DISICNT register to zero, as shown in
Example 5. A macro may also be used to perform
this task, as shown in Example 6.
DS80397A-page 5