PIC16LF873A-I/SS Microchip Technology, PIC16LF873A-I/SS Datasheet - Page 108

• Manufacturer Part Number: PIC16LF873A-I/SS
• Description: IC MCU FLASH 4KX14 EE A/D 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16LF873A-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 28-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Eeprom Size: 128 x 8
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 192 B
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• Data Rom Size: 128 B
• Height: 1.75 mm
• Length: 10.2 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 5.3 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: PIC16LF873AI/SS

PIC16F87XA
9.4.17.1
During a Start condition, a bus collision occurs if:
a)
b)
During a Start condition, both the SDA and the SCL
pins are monitored.
If the SDA pin is already low, or the SCL pin is already
low, then all of the following occur:
• the Start condition is aborted,
• the BCLIF flag is set and
• the MSSP module is reset to its Idle state
The Start condition begins with the SDA and SCL pins
deasserted. When the SDA pin is sampled high, the
Baud Rate Generator is loaded from SSPADD<6:0>
and counts down to 0. If the SCL pin is sampled low
while SDA is high, a bus collision occurs because it is
assumed that another master is attempting to drive a
data ‘1’ during the Start condition.
FIGURE 9-26:
DS39582B-page 106
(Figure 9-26).
SDA or SCL are sampled low at the beginning of
the Start condition (Figure 9-26).
SCL is sampled low before SDA is asserted low
(Figure 9-27).
SDA
SCL
SEN
BCLIF
S
SSPIF
Bus Collision During a Start
Condition
Set SEN, enable Start
condition if SDA = 1, SCL = 1
BUS COLLISION DURING START CONDITION (SDA ONLY)
SDA sampled low before
Start condition. Set BCLIF.
S bit and SSPIF set because
SDA = 0, SCL = 1.
SDA goes low before the SEN bit is set.
Set BCLIF,
S bit and SSPIF set because
SDA = 0, SCL = 1.
SSPIF and BCLIF are
cleared in software
If the SDA pin is sampled low during this count, the
BRG is reset and the SDA line is asserted early
(Figure 9-28). If, however, a ‘1’ is sampled on the SDA
pin, the SDA pin is asserted low at the end of the BRG
count. The Baud Rate Generator is then reloaded and
counts down to 0 and during this time, if the SCL pin is
sampled as ‘0’, a bus collision does not occur. At the
end of the BRG count, the SCL pin is asserted low.
Note:
SEN cleared automatically because of bus collision.
SSP module reset into Idle state.
The reason that bus collision is not a factor
during a Start condition is that no two bus
masters can assert a Start condition at the
exact same time. Therefore, one master
will always assert SDA before the other.
This condition does not cause a bus colli-
sion because the two masters must be
allowed to arbitrate the first address fol-
lowing the Start condition. If the address is
the same, arbitration must be allowed to
continue into the data portion, Repeated
Start or Stop conditions.
SSPIF and BCLIF are
cleared in software
 2003 Microchip Technology Inc.