DSPIC30F3010-30I/SO Microchip Technology, DSPIC30F3010-30I/SO Datasheet - Page 115
![IC DSPIC MCU/DSP 24K 28SOIC](/photos/6/59/65909/150-28-soic_sml.jpg)
DSPIC30F3010-30I/SO
Manufacturer Part Number
DSPIC30F3010-30I/SO
Description
IC DSPIC MCU/DSP 24K 28SOIC
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F3010-30ISO.pdf
(228 pages)
2.DSPIC30F3010-30ISO.pdf
(18 pages)
3.DSPIC30F3010-30ISO.pdf
(6 pages)
4.DSPIC30F3010-30ISO.pdf
(16 pages)
5.DSPIC30F3010-30ISO.pdf
(22 pages)
6.DSPIC30F3014-30IP.pdf
(244 pages)
Specifications of DSPIC30F3010-30I/SO
Program Memory Type
FLASH
Program Memory Size
24KB (8K x 24)
Package / Case
28-SOIC (7.5mm Width)
Core Processor
dsPIC
Core Size
16-Bit
Speed
30 MIPs
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
20
Eeprom Size
1K x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Product
DSCs
Data Bus Width
16 bit
Processor Series
DSPIC30F
Core
dsPIC
Maximum Clock Frequency
30 MHz
Data Ram Size
1 KB
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, DM240002, DM300027, DM330011, DM300018, DM183021
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
DSPIC30F301030ISO
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DSPIC30F3010-30I/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
17.7
The I
(I
Interrupt Flag). The MI2CIF interrupt flag is activated
on completion of a master message event. The SI2CIF
interrupt flag is activated on detection of a message
directed to the slave.
17.8
The I
and SCL signals for Fast mode (400 kHz). The control
bit, DISSLW, enables the user to disable slew rate
control, if desired. It is necessary to disable the slew
rate control for 1 MHz mode.
17.9
The control bit, IPMIEN, enables the module to support
Intelligent Peripheral Management Interface (IPMI).
When this bit is set, the module accepts and acts upon
all addresses.
17.10 General Call Address Support
The general call address can address all devices.
When this address is used, all devices should, in
theory, respond with an Acknowledgement.
The general call address is one of eight addresses
reserved for specific purposes by the I
consists of all ‘0’s with R_W = 0.
The general call address is recognized when the Gen-
eral Call Enable (GCEN) bit is set (I2CCON<7> = 1).
Following a Start bit detection, 8 bits are shifted into
I2CRSR and the address is compared with I2CADD,
and is also compared with the general call address
which is fixed in hardware.
If a general call address match occurs, the I2CRSR is
transferred to the I2CRCV after the eighth clock, the
RBF flag is set, and on the falling edge of the ninth bit
(ACK bit), the Master Event Interrupt Flag (MI2CIF) is
set.
When the interrupt is serviced, the source for the
interrupt can be checked by reading the contents of the
I2CRCV to determine if the address was device-specific,
or a general call address.
© 2010 Microchip Technology Inc.
2
C Master Interrupt Flag) and SI2CIF (I
2
2
C module generates two interrupt flags, MI2CIF
C standard requires slope control on the SDA
Interrupts
Slope Control
IPMI Support
2
C protocol. It
2
C Slave
17.11 I
As a master device, six operations are supported:
• Assert a Start condition on SDA and SCL
• Assert a Restart condition on SDA and SCL
• Write to the I2CTRN register initiating
• Generate a Stop condition on SDA and SCL
• Configure the I
• Generate an ACK condition at the end of a
17.12 I
The master device generates all of the serial clock
pulses and the Start and Stop conditions. A transfer is
ended with a Stop condition or with a Repeated Start
condition. Since the Repeated Start condition is also
the beginning of the next serial transfer, the I
not be released.
In Master Transmitter mode, serial data is output
through SDA, while SCL outputs the serial clock. The
first byte transmitted contains the slave address of the
receiving device (7 bits) and the data direction bit. In
this case, the data direction bit (R_W) is logic ‘0’. Serial
data is transmitted 8 bits at a time. After each byte is
transmitted, an ACK bit is received. Start and Stop
conditions are output to indicate the beginning and the
end of a serial transfer.
In Master Receive mode, the first byte transmitted
(7 bits) and the data direction bit. In this case, the data
direction bit (R_W) is logic ‘1’. Thus, the first byte
indicate the receive bit. Serial data is received via
SDA, while SCL outputs the serial clock. Serial data is
received 8 bits at a time. After each byte is received,
an ACK bit is transmitted. Start and Stop conditions
17.12.1
Transmission of a data byte, a 7-bit address or the
second half of a 10-bit address is accomplished by
simply writing a value to I2CTRN register. The user
should only write to I2CTRN when the module is in a
Wait state. This action will set the Buffer Full Flag (TBF)
and allow the Baud Rate Generator to begin counting
and start the next transmission. Each bit of address/
data will be shifted out onto the SDA pin after the falling
edge of SCL is asserted. The Transmit Status Flag,
TRSTAT (I2CSTAT<14>), indicates that a master
transmit is in progress.
contains the slave address of the transmitting device
transmitted is a 7-bit slave address, followed by a ‘1’ to
indicate the beginning and end of transmission.
transmission of data/address
received byte of data
dsPIC30F3010/3011
2
2
C Master Support
C Master Operation
I
2
C MASTER TRANSMISSION
2
C port to receive data
DS70141F-page 115
2
C bus will