DSPIC30F2010-30I/MM Microchip Technology, DSPIC30F2010-30I/MM Datasheet - Page 172

• Manufacturer Part Number: DSPIC30F2010-30I/MM
• Description: IC DSPIC MCU/DSP 12K 28QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F2010-30I/MM

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-QFN
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 20
• Flash Memory Size: 12KB
• Supply Voltage Range: 2.5V To 5.5V
• Package: 28QFN-S EP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 20
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F2010-30I/MMG; DSPIC30F201030IMM; DSPIC30F201030IMM

dsPIC30F2010
DS70118J-page 172
FIGURE 22-17:
TABLE 22-33: SPI MODULE MASTER MODE (CKE = 1) TIMING REQUIREMENTS
AC CHARACTERISTICS
SP10
SP11
SP20
SP21
SP30
SP31
SP35
SP36
SP40
SP41
Note 1:
Param
No.
Note: Refer to
SCK
(CKP = 0)
(CKP = 1)
SDO
SDI
SCK
2:
3:
4:
X
X
X
X
TscL
TscH
TscF
TscR
TdoF
TdoR
TscH2doV,
TscL2doV
TdoV2sc,
TdoV2scL
TdiV2scH,
TdiV2scL
TscH2diL,
TscL2diL
These parameters are characterized but not tested in manufacturing.
Data in “Typ” column is at 5V, 25°C unless otherwise stated. Parameters are for design guidance only and
are not tested.
The minimum clock period for SCK is 100 ns. Therefore, the clock generated in Master mode must not
violate this specification.
Assumes 50 pF load on all SPI pins.
Symbol
Figure 22-2
SP36
SPI MODULE MASTER MODE (CKE =1) TIMING CHARACTERISTICS
SCK
SCK
SCK
SCK
SDO
SDO
SDO
SCK
SDO
first SCK
Setup time of SDI
to SCK
Hold time of SDI
to SCK
SP40
MSb IN
X
X
X
X
X
X
X
X
X
Characteristic
MSb
output low time
output high time
output fall time
output rise time
edge
data output fall time
data output rise time
data output valid after
data output setup to
X
X
SP11
SP41
for load conditions.
X
edge
edge
edge
SP30,SP31
SP35
X
X
SP10
data input
data input
(1)
(4)
(3)
(4)
(3)
BIT14 - - - - - -1
BIT14 - - - -1
(4)
(4)
Standard Operating Conditions: 2.5V to 5.5V
(unless otherwise stated)
Operating temperature
T
T
Min
CY
CY
30
20
20
—
—
—
—
—
/2
/2
SP21
SP20
Typ
LSb IN
—
—
—
—
—
—
—
—
—
—
LSb
(2)
SP20
SP21
-40°C ≤ T
-40°C ≤ T
Max
30
—
—
—
—
—
—
—
—
—
© 2011 Microchip Technology Inc.
A
A
≤ +85°C for Industrial
≤ +125°C for Extended
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
See Note 3
See Note 3
See parameter
DO32
See parameter
DO31
See parameter
DO32
See parameter
DO31
Conditions
—
—
—
—