PIC18F26J50-I/SS Microchip Technology, PIC18F26J50-I/SS Datasheet - Page 374

• Manufacturer Part Number: PIC18F26J50-I/SS
• Description: IC PIC MCU FLASH 64K 2V 28-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26J50-I/SS

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• Interface: EUSART, I2C, SPI, USB
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DV164136, MA180024, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Package: 28SSOP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F46J50 FAMILY
EQUATION 21-2:
DS39931C-page 374
For this example, the following assumptions are made about the application:
• 3.3V will be applied to V
• This is a full-speed application that uses one interrupt IN endpoint that can send one packet of 64 bytes every
• A regular USB “B” or “mini-B” connector will be used on the application circuit board.
In this case, P
IN endpoint. All 64 kbps of data could potentially be bytes of value, 00h. Since ‘0’ bits cause toggling of the output state
of the transceiver, they cause the USB transceiver to consume extra current charging/discharging the cable. In this
case, 100% of the data bits sent can be of value ‘0’. This should be considered the “max” value, as normal data will
consist of a fair mix of ones and zeros.
This application uses 64 kbps for IN traffic out of the total bus bandwidth of 1.5 Mbps (12 Mbps), therefore:
Since a regular “B” or “mini-B” connector is used in this application, the end user may plug in any type of cable up to
the maximum allowed 5m length. Therefore, we use the worst-case length:
Assume I
USB bandwidth is shared between all the devices which are plugged into the root port (via hubs). If the application is
plugged into a USB 1.1 hub that has other devices plugged into it, your device may see host to device traffic on the
bus, even if it is not addressed to your device. Since any traffic, regardless of source, can increase the I
above the base 218 μA, it is safest to allow for the worst-case of 2.2 mA.
Therefore:
1 ms, with no restrictions on the values of the bytes being sent. The application may or may not have additional
traffic on OUT endpoints.
L
CABLE
† The calculated value should be considered an approximation and additional guardband or
PULLUP
application-specific product testing is recommended. The transceiver current is “in addition to” the
rest of the current consumed by the PIC18F46J50 Family device that is needed to run the core,
drive the other I/O lines, power the various modules, etc.
= 5 meters
ZERO
= 2.2 mA. The actual value of I
= 100% = 1, because there should be no restriction on the value of the data moving through the
CALCULATING USB TRANSCEIVER CURRENT
USB
I
and V
XCVR
=
DD
(40 mA • 3.3V • 1 • 0.043 • 5m)
, with the core voltage regulator enabled.
Pin =
(3.3V • 5m)
PULLUP
1.5 Mbps
64 kbps
will likely be closer to 218 μA, but allow for the worst-case.
= 4.3% = 0.043
+ 2.2 mA = 3.9 mA
†
© 2009 Microchip Technology Inc.
PULLUP
current