PIC18LF13K50-I/P Microchip Technology, PIC18LF13K50-I/P Datasheet - Page 249
![IC PIC MCU FLASH 4KX16 20-PDIP](/photos/12/13/121303/150-20-dip_sml.jpg)
PIC18LF13K50-I/P
Manufacturer Part Number
PIC18LF13K50-I/P
Description
IC PIC MCU FLASH 4KX16 20-PDIP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.PIC18F13K50-ISS.pdf
(420 pages)
2.PIC18F13K50-ISS.pdf
(40 pages)
3.PIC18F13K50-ISS.pdf
(10 pages)
4.PIC18F13K50-ISS.pdf
(2 pages)
5.PIC18F13K50-ISO.pdf
(414 pages)
Specifications of PIC18LF13K50-I/P
Core Size
8-Bit
Program Memory Size
8KB (4K x 16)
Core Processor
PIC
Speed
48MHz
Connectivity
I²C, SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
14
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 11x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
20-DIP (0.300", 7.62mm)
Controller Family/series
PIC18
No. Of I/o's
15
Eeprom Memory Size
256Byte
Ram Memory Size
512Byte
Cpu Speed
48MHz
No. Of Timers
4
Processor Series
PIC18LF
Core
PIC
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
EUSART, I2C, MSSP, SPI, USB
Maximum Clock Frequency
32 KHz
Number Of Programmable I/os
18
Number Of Timers
4
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 125 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, DM164127, DV164126
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 12 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
- PIC18F13K50-ISS PDF datasheet
- PIC18F13K50-ISS PDF datasheet #2
- PIC18F13K50-ISS PDF datasheet #3
- PIC18F13K50-ISS PDF datasheet #4
- PIC18F13K50-ISO PDF datasheet #5
- Current page: 249 of 414
- Download datasheet (4Mb)
The PPBRST bit (UCON<6>) controls the Reset status
when Double-Buffering mode (ping-pong buffering) is
used. When the PPBRST bit is set, all Ping-Pong Buf-
fer Pointers are set to the Even buffers. PPBRST has
to be cleared by firmware. This bit is ignored in buffer-
ing modes not using ping-pong buffering.
The PKTDIS bit (UCON<4>) is a flag indicating that the
SIE has disabled packet transmission and reception.
This bit is set by the SIE when a SETUP token is
received to allow setup processing. This bit cannot be
set by the microcontroller, only cleared; clearing it
allows the SIE to continue transmission and/or
reception. Any pending events within the Buffer
Descriptor Table will still be available, indicated within
the USTAT register’s FIFO buffer.
The RESUME bit (UCON<2>) allows the peripheral to
perform a remote wake-up by executing Resume
signaling. To generate a valid remote wake-up,
firmware must set RESUME for 10 ms and then clear
the bit. For more information on “resume signaling”,
see the “Universal Serial Bus Specification
Revision 2.0”.
The SUSPND bit (UCON<1>) places the module and
supporting circuitry in a Low-Power mode. The input
clock to the SIE is also disabled. This bit should be set
by the software in response to an IDLEIF interrupt. It
should be reset by the microcontroller firmware after an
ACTVIF interrupt is observed. When this bit is active,
the device remains attached to the bus but the trans-
ceiver outputs remain Idle. The voltage on the V
may vary depending on the value of this bit. Setting this
bit before a IDLEIF request will result in unpredictable
bus behavior.
22.2.2
Prior to communicating over USB, the module’s
associated internal and/or external hardware must be
configured. Most of the configuration is performed with
the UCFG register (Register 22-2).The UFCG register
contains most of the bits that control the system level
behavior of the USB module. These include:
• Bus Speed (full speed versus low speed)
• On-Chip Pull-up Resistor Enable
• Ping-Pong Buffer Usage
© 200C Microchip Technology Inc.
Note:
While in Suspend mode, a typical
bus-powered USB device is limited to
500 μA of current. This is the complete
current which may be drawn by the PIC
device and its supporting circuitry. Care
should be taken to assure minimum
current draw when the device enters
Suspend mode.
USB CONFIGURATION REGISTER
(UCFG)
PIC18F1XK50/PIC18LF1XK50
USB
Preliminary
pin
The UTEYE bit, UCFG<7>, enables eye pattern gener-
ation, which aids in module testing, debugging and
USB certifications.
22.2.2.1
The USB peripheral has a built-in, USB 2.0, full-speed
and low-speed capable transceiver, internally con-
nected to the SIE. This feature is useful for low-cost,
single chip applications. Enabling the USB module
(USBEN = 1) will also enable the internal transceiver.
The FSEN bit (UCFG<2>) controls the transceiver
speed; setting the bit enables full-speed operation.
The on-chip USB pull-up resistors are controlled by the
UPUEN bit (UCFG<4>). They can only be selected
when the on-chip transceiver is enabled.
The internal USB transceiver obtains power from the
V
cations, V
between 3.0V and 3.6V. The best electrical signal qual-
ity is obtained when a 3.3V supply is used and locally
bypassed with a high quality ceramic capacitor. The
capacitor should be placed as close as possible to the
V
package (i.e., route ground of the capacitor to V
pin 20 on 20-lead PDIP, SOIC, and SSOP packaged
parts).
The D+ and D- signal lines can be routed directly to
their respective pins on the USB connector or cable (for
hard-wired applications). No additional resistors,
capacitors, or magnetic components are required as
the D+ and D- drivers have controlled slew rate and
output impedance intended to match with the
characteristic impedance of the USB cable.
In order to meet the USB specifications, the traces
should be less than 30 cm long. Ideally, these traces
should be designed to have a characteristic impedance
matching that of the USB cable.
USB
USB
Note:
pin. In order to meet USB signalling level specifi-
and V
USB
The USB speed, transceiver and pull-up
should only be configured during the mod-
ule setup phase. It is not recommended to
switch these settings while the module is
enabled.
SS
Internal Transceiver
must be supplied with a voltage source
pins found on the same edge of the
DS41350C-page 247
SS
Related parts for PIC18LF13K50-I/P
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.8VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-4.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.85VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: