PIC16F1938-I/ML Microchip Technology, PIC16F1938-I/ML Datasheet - Page 228

• Manufacturer Part Number: PIC16F1938-I/ML
• Description: IC MCU 8BIT FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1938-I/ML

• Core Size: 8-Bit
• Program Memory Size: 28KB (16K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16F
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1024Byte
• Cpu Speed: 32MHz
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 11-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC16F193X/LF193X
22.4.6
In Single Output mode, PWM steering allows any of the
PWM pins to be the modulated signal. Additionally, the
same PWM signal can be simultaneously available on
multiple pins.
Once
(CCPxM<3:2> = 11
CCPxCON register), the user firmware can bring out
the same PWM signal to one, two, three or four output
pins by setting the appropriate STRx<D:A> bits of the
PSTRxCON register, as shown in Table 22-8.
While the PWM Steering mode is active, CCPxM<1:0>
bits of the CCPxCON register select the PWM output
polarity for the Px<D:A> pins.
The PWM auto-shutdown operation also applies to
PWM Steering mode as described in Section 22.4.3
“Enhanced
auto-shutdown event will only affect pins that have
PWM outputs enabled.
FIGURE 22-18:
DS41364D-page 228
Note 1: Port outputs are configured as shown when
Note:
PORT Data
PORT Data
PORT Data
PORT Data
PxA Signal
CCPxM1
CCPxM0
CCPxM1
CCPxM0
2: Single PWM output requires setting at least
the
STRxC
STRxD
STRxA
STRxB
the CCPxCON register bits PxM<1:0> = 00
and CCPxM<3:2> = 11.
one of the STRx bits.
PWM STEERING MODE
The associated TRIS bits must be set to
output (‘0’) to enable the pin output driver
in order to see the PWM signal on the pin.
Single
PWM
and
Auto-shutdown
SIMPLIFIED STEERING
BLOCK DIAGRAM
Output
1
0
1
0
1
0
1
0
PxM<1:0> = 00
mode
TRIS
TRIS
TRIS
TRIS
PxB pin
PxC pin
PxD pin
mode”.
PxA pin
is
selected
of
Preliminary
the
An
 2009 Microchip Technology Inc.