PIC12F675-I/SN Microchip Technology, PIC12F675-I/SN Datasheet - Page 42

• Manufacturer Part Number: PIC12F675-I/SN
• Description: IC MCU CMOS FLSH-BASE 8BIT 8SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F675-I/SN

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-SOIC (3.9mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS- 232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 53270-913
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC12F629/675
REGISTER 6-2:
6.9
The comparator interrupt flag is set whenever there is
a change in the output value of the comparator.
Software will need to maintain information about the
status of the output bits, as read from CMCON<6>, to
determine the actual change that has occurred. The
CMIF bit, PIR1<3>, is the comparator interrupt flag.
This bit must be reset in software by clearing it to ‘0’.
Since it is also possible to write a '1' to this register, a
simulated interrupt may be initiated.
The
(INTCON<6>) must be set to enable the interrupt. In
addition, the GIE bit must also be set. If any of these
bits are cleared, the interrupt is not enabled, though the
CMIF bit will still be set if an interrupt condition occurs.
TABLE 6-2:
DS41190C-page 40
0Bh/8Bh
0Ch
19h
8Ch
85h
99h
Legend:
Address
CMIE
Comparator Interrupts
bit 7
bit 6
bit 5
bit 4
bit 3-0
INTCON
PIR1
CMCON
PIE1
TRISIO
VRCON
Name
x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used by the comparator module.
bit
REGISTERS ASSOCIATED WITH COMPARATOR MODULE
(PIE1<3>)
VREN
VRCON — VOLTAGE REFERENCE CONTROL REGISTER (ADDRESS: 99h)
Bit 7
EEIF
EEIE
bit 7
VREN: CV
1 = CV
0 = CV
Unimplemented: Read as '0'
VRR: CV
1 = Low range
0 = High range
Unimplemented: Read as '0'
VR3:VR0: CV
When VRR = 1: CV
When VRR = 0: CV
GIE
Legend:
R = Readable bit
- n = Value at POR
—
—
R/W-0
VREN
REF
REF
COUT
PEIE
ADIF
ADIE
Bit 6
and
REF
—
—
REF
circuit powered on
circuit powered down, no I
Range Selection bit
REF
Enable bit
U-0
the
TRISIO5 TRISIO4 TRISIO3 TRISIO2 TRISIO1 TRISIO0
—
Bit 5
T0IE
VRR
value selection 0 ≤ VR [3:0] ≤ 15
—
—
—
REF
REF
PEIE
= (VR3:VR0 / 24) * V
= V
R/W-0
CINV
Bit 4
INTE
VRR
DD
—
—
—
W = Writable bit
’1’ = Bit is set
bit
/4 + (VR3:VR0 / 32) * V
GPIE
CMIF
CMIE
Bit 3
VR3
CIS
R/W-0
DD
—
The user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
b)
A mismatch condition will continue to set flag bit CMIF.
Reading CMCON will end the mismatch condition, and
allow flag bit CMIF to be cleared.
drain
Note:
Bit 2
CM2
T0IF
VR2
Any read or write of CMCON. This will end the
mismatch condition.
Clear flag bit CMIF.
DD
—
—
R/W-0
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
VR3
If a change in the CMCON register (COUT)
should occur when a read operation is
being executed (start of the Q2 cycle), then
the CMIF (PIR1<3>) interrupt flag may not
get set.
Bit 1
INTF
CM1
VR1
DD
—
—
TMR1IE
TMR1IF
R/W-0
GPIF
Bit 0
CM0
VR0
VR2
 2003 Microchip Technology Inc.
0000 0000
00-- 0--0
-0-0 0000
00-- 0--0
--11 1111
0-0- 0000
POR, BOD
Value on
x = Bit is unknown
R/W-0
VR1
0000 000u
00-- 0--0
-0-0 0000
00-- 0--0
--11 1111
0-0- 0000
Value on
RESETS
all other
R/W-0
VR0
bit 0