TOOLSTICK540DC Silicon Laboratories Inc, TOOLSTICK540DC Datasheet - Page 13
![DAUGHTER CARD TOOLSTICK F540](/photos/9/25/92540/toolstick540dc_sml.jpg)
TOOLSTICK540DC
Manufacturer Part Number
TOOLSTICK540DC
Description
DAUGHTER CARD TOOLSTICK F540
Manufacturer
Silicon Laboratories Inc
Series
ToolStickr
Type
MCUr
Datasheets
1.TOOLSTICK540DC.pdf
(274 pages)
2.TOOLSTICK540DC.pdf
(16 pages)
3.TOOLSTICK540DC.pdf
(12 pages)
Specifications of TOOLSTICK540DC
Contents
Daughter Card
Processor To Be Evaluated
C8051F54x
Processor Series
C8051F54x
Interface Type
USB
Operating Supply Voltage
2.7 V to 3.6 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
C8051F54x
For Use With
336-1345 - TOOLSTICK BASE ADAPTER336-1182 - ADAPTER USB DEBUG FOR C8051FXXX
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1717
7. Additional Demo Examples
In addition to the F540DC_FeaturesDemo example firmware, the ToolStick download package also includes a
demo project named F540DC_ADC0_TemperatureSensor. The instructions for running this demo can be found at
the top of the source file. The project and source files for these demos can be found in the
C:\SiLabs\MCU\ToolStick\F540DC\Firmware\ (default) folder.
8. Using the C8051F540 Daughter Card as a Development Platform
The prototyping area on the ToolStick C8051F540 Daughter Card makes it easy to interface to external hardware.
All of the digital I/O pins are available so it is possible to create a complete system.
8.1. C8051F540 Pin Connections
It is important to note that if external hardware is being added, some of the existing components on the board can
interfere with the signaling. The following is a list of port pins on the C8051F540 that are connected to other
components:
See the daughter card schematic in Section 10 for more information.
8.2. Local Interconnect Network (LIN) Transceiver
The C8051F540 daughter card includes a LIN transceiver to enable communication on LIN networks. The LIN
transceiver requires a higher voltage than the 5 V provided by the USB interface and so a voltage converter is
provided to double the 5 V USB voltage to 10 V. The LIN transceiver can also be powered through the TB1 external
header. If both voltage sources are present, the higher voltage is automatically selected for the transceiver.
8.3. C2 Pin Sharing
On the C8051F540, the debug pins, C2CK, and C2D, are shared with the pins RST and P3.0 respectively. The
daughter card includes the resistors necessary to enable pin sharing, which allow the RST and P3.0 pins to be
used normally while simultaneously debugging the device. See Application Note “AN124: Pin Sharing Techniques
for the C2 Interface” at
9. Information Locations
Example source code is installed by default in the “C:\SiLabs\MCU\ToolStick\F540DC\Firmware” directory during
the ToolStick installation.
Documentation
C:\SiLabs\MCU\ToolStick\Documentation and the C:\SiLabs\MCU\ToolStick\F540DC\Documentation directories.
The installer for the ToolStick software is available at www.silabs.com/toolstick.
P0.0—This pin is connected to a 1.0 uF capacitor, which serves as a decoupling capacitor for the on-chip
voltage reference. The capacitor C3 can be removed to disconnect it from the pin.
P0.4, P0.5—These pins are connected directly to the ToolStick Base Adapter for UART communication.
P1.0, P1.1—These pins are connected to the TXD and RXD pins of the LIN transceiver. The LIN transceiver
can be removed to disconnect it from the pins.
P1.2—This pin is connected to the anode of the green LED on the daughter card. The LED or the R2 resistor
can be removed to disconnect the LED from the pin.
P1.3—This pin is connected to the output of the potentiometer. The 0 ohm resistor R5 can be removed to
disconnect the potentiometer from the pin.
P1.4—This pin is connected to the P1.4 switch. The switch can be removed to disconnect it from the pin.
P1.5, P1.6—These pins are connected directly to the ToolStick Base Adapter’s GPIO pins. By default, these
GPIO pins on the Base Adapter are high-impedance pins so they will not affect any signaling. Configuring these
pins on the Base Adapter to output pins or handshaking pins could affect signaling.
for
www.silabs.com
the
ToolStick
for more information regarding pin sharing.
kit,
including
Rev. 0.1
this
User’s
ToolStick-F540DC
Guide,
can
be
found
in
the
13