KIT3468MMA7455L Freescale Semiconductor, KIT3468MMA7455L Datasheet - Page 16

• Manufacturer Part Number: KIT3468MMA7455L
• Description: KIT EVALUATION FOR MMA7456L
• Manufacturer: Freescale Semiconductor

Specifications of KIT3468MMA7455L

• Sensor Type: Accelerometer, 3 Axis
• Sensing Range: ±2g, 4g, 8g
• Interface: I²C, SPI
• Sensitivity: 16, 32, 64 LSB/g
• Voltage - Supply: 2.4 V ~ 3.6 V
• Embedded: No
• Utilized Ic / Part: MMA7455
• Acceleration: 2 g, 4 g, 6 g
• Sensing Axis: Triple Axis
• Output Type: Digital
• Operating Voltage: 3.6 V
• Operating Current: 400 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Detecting Interrupts
LDX
1: Level detection event is detected on X-axis
0: Level detection event is not detected on X-axis
LDY
1: Level detection event is detected on Y-axis
0: Level detection event is not detected on Y-axis
LDZ
1: Level detection event is detected on Z-axis
0: Level detection event is not detected on Z-axis
PDX
1: 1
0: 1
PDY
1: 1
0: 1
DIGITAL INTERFACE
The MMA7455L has both an I
mode of communication. When CS is low, SPI communication is selected. When CS is high, I
Note: It is recommended to disable I
ferent SPI communication protocol. To disable I
I
I
microcontroller, which provides the serial clock signal and addresses the slave device(s) on the bus. The MMA7455L communi-
cates only in slave operation where the device address is $1D. Multiple read and write modes are available. The protocol supports
slave only operation. It does not support Hs mode, “10-bit addressing”, “general call” and: ”START byte”.
SINGLE BYTE READ
The MMA7455L has an 10-bit ADC that can sample, convert and return sensor data on request. The transmission of an 8-bit
command begins on the falling edge of SCL. After the eight clock cycles are used to send the command, note that the data re-
turned is sent with the MSB first once the data is received.
read operation. The Master (or MCU) transmits a start condition (ST) to the MMA7455L, slave address ($1D), with the R/W bit
set to “0” for a write, and the MMA7455L sends an acknowledgement. Then the Master (or MCU) transmits the 8-bit address of
the register to read and the MMA7455L sends an acknowledgement. The Master (or MCU) transmits a repeated start condition
(SR) and then addresses the MMA7455L ($1D) with the R/W bit set to “1” for a read from the previously selected register. The
Slave then acknowledges and transmits the data from the requested register. The Master does not acknowledge (NAK) it re-
ceived the transmitted data, but transmits a stop condition to end the data transfer.
MULTIPLE BYTES READ
The MMA7455L automatically increments the received register address commands after a read command is received. Therefore,
after following the steps of a single byte read, multiple bytes of data can be read from sequential registers after each MMA7455L
acknowledgment (AK) is received until a NACK is received from the Master followed by a stop condition (SP) signalling an end
of transmission. See
$0A: Detection Source Register (Read only)
16
MMA7455L
2
2
C Slave Interface
C is a synchronous serial communication between a master device and one or more slave devices. The master is typically a
st
st
st
st
LDX
D7
pulse is detected on X-axis
pulse is detected on X-axis
pulse is detected on Y-axis
pulse is detected on Y-axis
0
LDY
D6
0
Figure
8.
2
C and SPI digital output available for a communication interface. CS pin is used for selecting the
LDZ
D5
0
2
C during SPI communication to avoid communication errors between devices using a dif-
PDX
2
D4
C, set the I
0
Figure 7
2
CDIS bit in I
PDY
D3
0
PDZ
1: 1
0: 1
INT1
1: Interrupt assigned by INTRG[1:0] bits in Control 1
Register ($18) and is detected
0: Interrupt assigned by INTRG[1:0] bits in Control 1
Register ($18) and is not detected
INT2
1: Interrupt assigned by INTRG[1:0] bits in Control 1
Register ($18) and is detected
0: Interrupt assigned by INTRG[1:0] bits in Control 1
Register ($18) and is not detected
shows the timing diagram for the accelerometer 8-bit I
st
st
pulse is detected on Z-axis
pulse is detected on Z-axis
2
C Device Address register using SPI.
PDZ
D2
0
INT2
D1
0
2
C communication is selected.
Freescale Semiconductor
INT1
D0
0
Reg $0A
Function
Default
Sensors
2
C