MPDTY111S Murata Electronics North America, MPDTY111S Datasheet - Page 9

• Manufacturer Part Number: MPDTY111S
• Description: CONV DC/DC 6W 1.0VOUT 6A SMT
• Manufacturer: Murata Electronics North America
• Series: MPDr
• Type: Point of Load (POL) Non-Isolated with UVLOr

Specifications of MPDTY111S

• Output: 1V
• Number Of Outputs: 1
• Power (watts): 6W
• Mounting Type: Surface Mount
• Voltage - Input: 3 ~ 3.63V
• Package / Case: 12-DIP SMD Module
• 1st Output: 1 VDC @ 6A
• Size / Dimension: 1.33" L x 0.61" W x 0.24" H (33.8mm x 15.4mm x 6mm)
• Power (watts) - Rated: 6W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 93%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Other names: 490-4558

1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
Note:
9.3. Reliability
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
specifications or transact the approval sheet for product specifications before ordering.
9.3.1. Humidity Test
9.3.2. Thermal Cycle Test
9.3.3. Vibration
9.3.4. Mechanical Shock
9.3.5. Soldering Heat Resistance
9.3.6. Lead Pin Strength
9.3.7. Solderability of Leads
Parts are subjected to a temperature 40°C±2°C with 90∼95% for 100 hours.
Return the parts to room temperature (25°C) for 4 hours and measure. The initial values under item
9-1 should be met. (JIS-C-0022)
Then tested products are left for 2 hours.
The parts are placed in room temperature (25°C) for 2 hours and are measured.
The initial values under item 9-1 should be met.
10 to 55Hz, 1.5mm amplitude, 1 hour for each each of X,Y,Z directions.
No damage in appearance and no deviation from electrical characteristics(9-1).
20G, 1 time for each X,Y,Z directions.
No damage in appearance and no deviation from electrical characteristics(9-1).
Immerse the part of lead where it is to be soldered on a motherboard in a solder bath of 260±5°C
for 3±0.5s.
There is no damage in appearance and no deviation from electrical characteristics in clause 9.
Parts are subjected to 5 cycle of the following.
The lead pins will be immersed in the Isopropyl Alcohol (JIS K 1522) with Rosin (JIS K 5902) solution
(the concentration of Rosin will be allowed 10wt% to 35wt%, and normally approx.25wt% will be used
without any specific requirement.). Then the lead pins will be immersed in the solder H63A (JIS Z 3282)
solution at the temperature of 230°C±5°C for 3±0.5seconds, and pulled up completely. The solder will
adhere to over 75% of immersed area.
Strain a lead pin by gradual-increasingly 5.0N along axial direction; withstand for 5s.
No damage on a lead pin.
Step
1
2
3
4
Room Temp.
Room Temp.
+85±3°C
Condition
-40±3°C
5∼10 minutes
5∼10 minutes
30 minutes
30 minutes
Time
MPD6D12*S Specification
2010.5.7
9