GP1FP513TK0F Sharp Microelectronics, GP1FP513TK0F Datasheet
GP1FP513TK0F
Specifications of GP1FP513TK0F
Related parts for GP1FP513TK0F
GP1FP513TK0F Summary of contents
Page 1
... GP1FP513TK0F ■ Description GP1FP513TK0F has a built-in LED with a peak light emission wavelength of 660 nm and the associated drive IC, and the input is TTL level compatible. ■ Features 1. Fiber optic transmitter (Receiver : GP1FP513RK0F) 2. Electric jack/Optical connector integrated type (Electric jack : JEITA RC-5231 Optical connector : JEITA RC-5720B) 3 ...
Page 2
... Model No. and date code, [2] portion : material shall be indicated. ( > PBT < 4) Unspecified tolerance shall be ± 0.3. 5) Dimensions in parenthesis are shown for reference. Material Finish - SPCC Ni plating Brass Sn plating SPCC Sn plating - - - Cu alloy SnCu plating datum face Jan to Sep Oct Nov Dec GP1FP513TK0F (Unit: mm) Product mass : approx Sheet No.: E2-A00802EN ...
Page 3
... LED Driver IC d3 LED : GaAlAs, Driver IC : Silicon *1 Input conditions of V terminal are designed to conform to TTL and CMOS recommend that the input fore V high speed CMOS. p2 <Pin jack> GP1FP513TK0F (Unit: mm) Pin arrangement GND p1 : data GND d1 d3 terminal uses the output of TTL and ...
Page 4
... CC V Measuring method refer to Fig pLH t pHL Measuring method refer to Fig Δt w Δt j Rating Unit -20 to +70 °C -30 to +70 °C 260 ° less/time times. *2 AC500V - 1 min. rms value 4 GP1FP513TK0F Remark Remark ( ° MIN. TYP. MAX. 630 660 690 -21 - 180 - - 180 -15 - ...
Page 5
... The optical power meter must be calibrated to 660 nm. (0 dBm = 1 mW) D The optical power meter must be calibrated to 660 nm. (0 dBm = 1 mW) Judgment method ≤ -15 dBm less C CC ≤ -36 dBm less GP1FP513TK0F Optical power meter (Anritsu) ML93B Optical power meter (Anritsu) ML93B Sheet No.: E2-A00802EN ...
Page 6
... The wave form write time shall But do not allow the wave form to be distorted by increasing the brightness too much. ( 5.0 V (State of operating) CC (3) The probe for the oscilloscope must be more than 1 MΩ and less than 10 pF. CH1 CH2 50% t pHL 50% ∆t ∆ GP1FP513TK0F Output signal Standard receiver Oscilloscope (band width: 1 GHz) Trigger: CH1 Mode: Storage mode Sheet No.: E2-A00802EN ...
Page 7
... Please do not stress the connector coupling portion excessively since there might be a case that the shutter can’t operate normally. (10) About getting the flux into connector coupling portion Please avoid getting a flux into connector coupling portion of this device, because there might be a case that the characteristics deteriorate the shutter can’t operate normally. 7 GP1FP513TK0F Sheet No.: E2-A00802EN ...
Page 8
... This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC). • Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE). ■ Packing Specifications Product Tray Product Cross section of tray PACKING MATERIAL Tray : Polystyrene PACKING METHOD Each tray holds 100 pieces. 8 GP1FP513TK0F Sheet No.: E2-A00802EN ...
Page 9
... SHARP. Express written permission is also required before any use of this publication may be made by a third party. · Contact and consult with a SHARP representative if there are any questions about the contents of this publication. 9 GP1FP513TK0F Sheet No.: E2-A00802EN ...