P1TX4A-SX4-V-01 Omron, P1TX4A-SX4-V-01 Datasheet
P1TX4A-SX4-V-01
Specifications of P1TX4A-SX4-V-01
Z2549
Related parts for P1TX4A-SX4-V-01
P1TX4A-SX4-V-01 Summary of contents
Page 1
... OMRON MRON ETWORK RODUCTS P1TX/RX4A-SX4 Interface Information & Reference Designs ORIGINATOR: B. Peters Omron SX4 Reference Design ® LAST REVISED BY: B. Peters 5/23/07 P1xX4A-SX4-01 Reference Designs Rev 2.4 APPROVED BY: REV DOCUMENT NO. 2.4 DOC00617 1 11 SHEET OF ...
Page 2
... Block Diagram ........................................................................................................ 3 2.0 Microcontroller Circuit Design............................................................................... 3 3.0 Microcontroller Interface ........................................................................................ 4 4.0 I and I Settings ............................................................................................... 5 bias mod 5.0 Mounting Configurations........................................................................................ 7 ORIGINATOR: B. Peters Omron SX4 Reference Design ® LAST REVISED BY: B. Peters 5/23/07 P1xX4A-SX4-01 Reference Designs Rev 2.4 APPROVED BY: REV DOCUMENT NO. 2.4 DOC00617 2 11 SHEET OF ...
Page 3
... RODUCTS 1.0 End of Life The P1TX4A-SX4 and P1RX4A-SX4 will be replaced by the P1TX4C-SX4 and P1RX4C-SX4 in 2007. The new version will be compatible, via only change to the microcontroller code, with designs that adhere to Omron’s reference design guidelines. This document only addresses the P1TX4A-SX4 and P1RX4A-SX4. ...
Page 4
... RODUCTS 4.0 Microcontroller Interface The P1TX4A-SX4 contains the AMCC S7022 laser driver that uses a three-line serial interface - serial clock (SCK), serial enable (SEN) and a bi-directional serial data input/output (SIO enable the microcontroller to read/write to internal data registers. The serial clock signal is used as a reference for clocking data into and out of the serial input/output pin ...
Page 5
... RODUCTS 4.1 Software To assist you in programming your microcontroller to work with Omron’s OSAs, Omron can provide (upon written request) two pre-written, ready-to-load software files. The first file (s7022_tiny12.hex) is the flash file and the second file (s7022_initial_eeprom.eep) is the initial eeprom file. The initial Bias and ...
Page 6
... Because of normal variations in laser characteristics, the I P1TX4-SX4 is shipped with documentation showing its optical I such, Omron strongly recommends that any system using the P1TX4-SX4 should be designed to allow access to the microcontroller, and the ability to enter specific the codes for registers 1 and 2 to match the appropriate setting. ...
Page 7
... Implementing this resistive network for TMDS will cause a 50% reduction in voltage delivered to the P1TX4C-SX4- 01. Designers must ensure that regardless of the input circuit chosen, the minimum specified Differential Input Voltage (section 5 of the P1TX4A-SX4x-01 Datasheet) is achieved. A TMDS buffer chip can be installed as an alternative, which will not reduce the voltage. ...
Page 8
... OMRON MRON ETWORK RODUCTS ORIGINATOR: B. Peters Omron SX4 Reference Design ® LAST REVISED BY: B. Peters 5/23/07 P1xX4A-SX4-01 Reference Designs Rev 2.4 APPROVED BY: REV DOCUMENT NO. 2.4 DOC00617 8 11 SHEET OF ...
Page 9
... Reference Design for ROSA Output Circuit Output C11 - C18 LVDS 0.1μF LVPECL 0.1μF CML Short TMDS Short ORIGINATOR: B. Peters Omron SX4 Reference Design ® LAST REVISED BY: B. Peters 5/23/07 P1xX4A-SX4-01 Reference Designs Rev 2.4 APPROVED BY: REV DOCUMENT NO. 2.4 DOC00617 9 11 ...
Page 10
... ETWORK RODUCTS 8.0 Using the Omron Connector The following pin map can be used to assist when designing-in the Omron flex connector to be used with the Omron ROSA or TOSA. For description of pins, see the OSA data sheet. Mating Board Pads (Top View) ZIF ...
Page 11
... Top Connect For those with space available on the CDR board, the flex can be connected to the top of the main CDR board via a ZIF connector (e.g. Omron P/N XF2B-2745-31A). 9.2 Bottom-connect For those with space constraints, the flex circuit can be connected to the bottom of the main board via the ZIF connector ...
Page 12
... Seller within 30 days of receipt of shipment. III. PRECAUTIONS 1. Suitability THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE BUYER’ ...