20-101-0303 Rabbit Semiconductor, 20-101-0303 Datasheet - Page 86
20-101-0303
Manufacturer Part Number
20-101-0303
Description
SMARTSCREEN OP7100 W/TOUCHSCREEN
Manufacturer
Rabbit Semiconductor
Datasheet
1.101-0303.pdf
(126 pages)
Specifications of 20-101-0303
Display Type
STN - Super-Twisted Nematic
Viewing Area
121.00mm L x 91.00mm W
Backlight
CCFL - White
Dot Pitch
0.36mm x 0.36mm
Dot Pixels
320 x 240 (QVGA)
Interface
Serial
Product
Prototyping Accessories
Processor Type
Z180
Sram
128 KB
Flash
512 KB
Number Of I/os
16
Backup Battery
3 V Lithium Coin Type
Operating Voltage
10 V to 30 V
Power Consumption
4.5 W
Interface Type
Ethernet
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Display Mode
-
Dot Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
20-101-0303
20-101-303
20-101-303
316-1175
20-101-303
20-101-303
316-1175
- Current page: 86 of 126
- Download datasheet (780Kb)
Mounting
A bezel and a gasket are included with the OP7100. When properly mount-
ed in a panel, the bezel of the OP7100 is designed to meet NEMA 4 speci-
fications for water resistance.
Since the OP7100 employs an LCD display, the viewing angle must be
considered when mounting the display. Install the OP7100 at a height and
angle that makes it easy for the operator to see the screen.
Bezel-Mount Installation
This section describes and illustrates how to bezel-mount the OP7100.
Follow these steps for bezel-mount installation.
1. Cut mounting holes in the mounting panel in accordance with the
2. Remove all eight 4-40 locking hex nuts from their studs on the bezel,
86
0.180
(4.5)
recommended dimensions in Figure 6-2, then use the bezel faceplate to
mount the OP7100 onto the panel.
and carefully “drop in” the OP7100 with the bezel and gasket attached.
Installation
0.125 D, 8x
(3)
1.620
(40)
Note that the contrast controls, both manual and software, act
as view-angle controls, and should be adjusted to provide
theoptimum display quality at the angle from which the display
will normally be viewed.
Figure 6-2. Recommended Cutout Dimensions
5.380
(137)
CUTOUT
7.000
(178)
OP7100
Related parts for 20-101-0303
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: