20-101-0303 Rabbit Semiconductor, 20-101-0303 Datasheet - Page 41
20-101-0303
Manufacturer Part Number
20-101-0303
Description
SMARTSCREEN OP7100 W/TOUCHSCREEN
Manufacturer
Rabbit Semiconductor
Datasheet
1.101-0303.pdf
(126 pages)
Specifications of 20-101-0303
Display Type
STN - Super-Twisted Nematic
Viewing Area
121.00mm L x 91.00mm W
Backlight
CCFL - White
Dot Pitch
0.36mm x 0.36mm
Dot Pixels
320 x 240 (QVGA)
Interface
Serial
Product
Prototyping Accessories
Processor Type
Z180
Sram
128 KB
Flash
512 KB
Number Of I/os
16
Backup Battery
3 V Lithium Coin Type
Operating Voltage
10 V to 30 V
Power Consumption
4.5 W
Interface Type
Ethernet
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Display Mode
-
Dot Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
20-101-0303
20-101-303
20-101-303
316-1175
20-101-303
20-101-303
316-1175
- Current page: 41 of 126
- Download datasheet (780Kb)
Any Rabbit Semiconductor controller or the OP7100 can be a master or a
slave. A network can have up to 255 slaves, but only one master.
A multidrop network requires termination/bias resistors to minimize reflec-
tions (echoing) and to keep the network line active during an idle state. The
OP7100 termination resistors are already installed, and by default are en-
abled by having jumpers installed on header J9. Remove the jumpers from
header J9, as shown in Figure 3-21, to disable or remove the termination
resistors. Only the first and last devices on a multidrop RS-485 network should
have the termination resistors enabled.
FD
J9
J10
Figure 3-21. Enabling/Disabling Termination Resistors
Only a single, solid conductor should be placed in a screw clamp terminal.
Bare copper, particularly if exposed to the air for a long period before
installation, can become oxidized. The oxide can cause a high-resistance
(~20 Ω) connection, especially if the clamping pressure is not sufficient.
To avoid oxidation, use tinned wires or clean, shiny copper wire. If you are
using multiple conductors or stranded wire, consider soldering the wire
bundle or using a crimp connector to avoid a later loss of contact pressure
to a spontaneous rearrangement of the wire bundle. Note that soldering a
stranded wire may make the wire subject to fatigue failure at the junction
with the solder if there is flexing or vibration.
OP7100
Hardware 41
Related parts for 20-101-0303
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: