LTC3404EMS8 Linear Technology, LTC3404EMS8 Datasheet
LTC3404EMS8
Specifications of LTC3404EMS8
Available stocks
Related parts for LTC3404EMS8
LTC3404EMS8 Summary of contents
Page 1
... MSOP package. For higher input voltage (11V abs max) applications, refer to the LTC1877 data sheet. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. Burst Mode is a registered trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. ...
Page 2
... PACKAGE/ORDER I FOR ATIO 0.3V) IN ORDER PART NUMBER LTC3404EMS8 LTC3404IMS8 LTC3404MPMS8 Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: Consult LTC Marketing for parts specified with wider operating temperature ranges. ...
Page 3
ELECTRICAL CHARACTERISTICS ● The denotes specifications which apply over –55°C to 125°C, otherwise specifications are 25° 3.6V unless otherwise specified. IN SYMBOL PARAMETER I Feedback Current VFB V Regulated Output Voltage FB ΔV Output Overvoltage ...
Page 4
LTC3404 W U TYPICAL PERFOR A CE CHARACTERISTICS Efficiency vs Input Voltage 100mA OUT I = 10mA 90 OUT I = 300mA OUT I = 1mA OUT 0.1mA OUT Burst Mode OPERATION ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS R vs Input Voltage DS(ON) 0.9 0.8 SYNCHRONOUS 0.7 SWITCH 0.6 0.5 MAIN SWITCH 0.4 0.3 0.2 0 INPUT VOLTAGE (V) 3404 G09 DC ...
Page 6
LTC3404 W U TYPICAL PERFOR A CE CHARACTERISTICS Load Step Response V OUT 100mV/DIV I L 500mA/DIV I TH 1V/DIV 40μs/DIV 10μ 1. 22μF OUT OUT L = 4.7μH ...
Page 7
CTIO AL DIAGRA BURST Y = “0” ONLY WHEN CONSTANT “1” Y DEFEAT X PLL LPF 8 SYNC/MODE 7 VCO – 0.6V FREQ + 3 SHIFT REF + 0.8V EA – ...
Page 8
LTC3404 U OPERATIO When the converter is in Burst Mode operation, the peak current of the inductor is set to approximately 250mA, even though the voltage at the I TH value. The voltage at the I pin drops when the ...
Page 9
U OPERATIO Slope Compensation and Inductor Peak Current Slope compensation provides stability in constant fre- quency architectures by preventing subharmonic oscilla- tions at high duty cycles accomplished internally by adding a compensating ramp to the inductor current signal ...
Page 10
LTC3404 U U APPLICATIO S I FOR ATIO inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Kool Mμ (from Magnetics, Inc very good, low loss core material for toroids with a ...
Page 11
U U APPLICATIO S I FOR ATIO Phase-Locked Loop and Frequency Synchronization The LTC3404 has an internal voltage-controlled oscillator and phase detector comprising a phase-locked loop. This allows the top MOSFET turn- locked to the rising edge of ...
Page 12
LTC3404 U U APPLICATIO S I FOR ATIO very low load currents can be misleading since the actual power lost consequence as illustrated in Figure 6. 1. The V quiescent current is due to two components: IN ...
Page 13
U U APPLICATIO S I FOR ATIO which is below the maximum junction temperature of 125°C. Note that at higher supply voltages, the junction tempera- ture is lower due to reduced switch resistance (R Checking Transient Response The regulator loop ...
Page 14
LTC3404 U U APPLICATIO S I FOR ATIO = 4.2V, ΔI Substituting V = 2.5V, V OUT 1.4MHz in equation (3) gives: ⎛ ⎞ − ⎟ = μ ...
Page 15
... MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 16
... IN to 500mA, 1MHz Operation, OUT Pin, Constant Frequency 600mA, OUT Up to 5A, V from 2.2V to 10V OUT 10V 10μ 600mA OUT 10μ 600mA OUT IN LT 0607 REV B • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2000 V IN 2. 3.3V 3404fb ...