LT4256-2CS8 Linear Technology, LT4256-2CS8 Datasheet - Page 6

• Manufacturer Part Number: LT4256-2CS8
• Description: IC CTRLR HOTSWAP HV AUTO 8SOIC
• Manufacturer: Linear Technology
• Type: Hot-Swap Controllerr

Specifications of LT4256-2CS8

• Applications: General Purpose
• Internal Switch(s): No
• Voltage - Supply: 10.8 V ~ 80 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

LT4256-1/LT4256-2
PI FU CTIO S
UV (Pin 1): Undervoltage Sense. UV is an input that
enables the output voltage. When UV is driven above 4V,
GATE will start charging and the output turns on. When
UV goes below 3.6V, GATE discharges and the output
shuts off.
Pulsing UV low for a minimum of 5µs after a current limit
fault cycle resets the fault latch (LT4256-1) and allows the
part to turn back on. This command is only accepted after
TIMER has discharged below 0.65V. To disable UV sens-
ing, connect UV to a voltage beween 5V and 44V.
FB (Pin 2): Power Good Comparator Input. FB monitors
the output voltage through an external resistive divider.
When the voltage on FB is lower than the high-to-low
threshold of 3.99V, PWRGD is pulled low and released
when FB is pulled above the 4.45V low-to-high threshold.
The voltage present on FB affects foldback current limit
(see Figure 7 and related discussion).
PWRGD (Pin 3): Power Good Output. PWRGD is pulled
low whenever the voltage on FB falls below the 3.99V high-
to-low threshold voltage. It goes into a high impedance
state when the voltage on FB exceeds the low-to-high
threshold voltage. An external pull-up resistor can pull
PWRGD to a voltage higher or lower than V
GND (Pin 4): Device Ground. This pin must be tied to a
ground plane for best performance.
TIMER (Pin 5): Timing Input. An external timing capacitor
from TIMER to GND programs the maximum time the part
is allowed to remain in current limit. When the part goes
into current limit, a 105µA pull-up current source starts to
charge the timing capacitor. When the voltage on TIMER
reaches 4.65V (typ), GATE pulls low; the TIMER pull-up
current will be turned off and the capacitor is discharged
by a 3µA pull-down current. When TIMER falls below 0.65V
(typ), GATE turns on again for the LT4256-2. UV must be
cycled low after TIMER has discharged below 0.65V (typ)
to reset the LT4256-1. If UV is not cycled low (LT4256-1),
GATE remains latched off and TIMER is discharged to near
GND. Under an output short-circuit condition, the
LT4256-2 cycles on and off with a 3% duty cycle.
6
U
U
U
CC
.
GATE (Pin 6): High Side Gate Drive for the External N-
Channel MOSFET. An internal charge pump guarantees at
least 10V of gate drive for V
and 4.5V of gate drive for V
10.8V and 20V. The rising slope of the voltage on GATE is
set by an external capacitor connected from GATE to GND
and an internal 32µA pull-up current source from the
charge pump output.
If the current limit is reached, the GATE voltage is adjusted
to maintain a constant voltage across the sense resistor
while the timing capacitor starts to charge. If the TIMER
voltage ever exceeds 4.65V, GATE is pulled low.
GATE is also pulled to GND whenever UV is pulled low, the
V
undervoltage threshold, or V
UVLO threshold (9.8V).
GATE is clamped internally to a maximum voltage of 11.6V
(typ) above V
ing this pin beyond the clamp voltage may damage the
part. A Zener diode is needed between the gate and source
of the external MOSFET to protect its gate oxide under
instantaneous short-circuit conditions. See Applications
Information.
SENSE (Pin 7): Current Limit Sense Input. A sense
resistor is placed in the supply path between V
SENSE. The current limit circuit regulates the voltage
across the sense resistor (V
current limit when FB is 2V or higher. If FB drops below
2V, the regulated voltage across the sense resistor de-
creases linearly to 14mV when FB is 0V.
To defeat current limit, connect SENSE to V
V
input ranges from 10.8V to 80V for normal operation.
I
LT4256-1/LT4256-2 for inputs less than 9.8V (typ).
CC
CC
CC
supply voltage drops below the externally programmed
is typically 1.8mA. An internal circuit disables the
(Pin 8): Input Supply Voltage. The positive supply
CC
under normal operating conditions. Driv-
CC
CC
CC
CC
supply voltages above 20V
– SENSE) to 55mV while in
supply voltages between
drops below the internal
CC
.
CC
425612fa
and