VNQ830M_04 STMICROELECTRONICS [STMicroelectronics], VNQ830M_04 Datasheet
VNQ830M_04
Related parts for VNQ830M_04
VNQ830M_04 Summary of contents
Page 1
TYPE R DS(on) VNQ830M 60 m (*) 6 A (*) (*) Per each channel CMOS COMPATIBLE INPUTS OPEN DRAIN STATUS OUTPUTS ON STATE OPEN LOAD DETECTION OFF STATE OPEN LOAD DETECTION SHORTED LOAD PROTECTION UNDERVOLTAGE AND OVERVOLTAGE SHUTDOWN LOSS ...
Page 2
VNQ830M BLOCK DIAGRAM V cc CLAMP GND1,2 INPUT1 STATUS1 LOGIC OVERTEMP. 1 INPUT2 STATUS2 OVERTEMP CLAMP GND3,4 INPUT3 STATUS3 LOGIC OVERTEMP. 3 INPUT4 STATUS4 OVERTEMP. 4 2/21 V CC1,2 OVERVOLTAGE UNDERVOLTAGE CLAMP 1 DRIVER 1 CURRENT LIMITER ...
Page 3
CURRENT AND VOLTAGE CONVENTIONS I S3,4 V CC3,4 V IN1 V STAT1 V IN2 V STAT2 V IN3 V STAT3 V IN4 (*) during reverse battery condition Fn CCn OUTn CONFIGURATION DIAGRAM (TOP VIEW) & ...
Page 4
VNQ830M THERMAL DATA (Per island) Symbol R Thermal Resistance Junction-lead per chip thj-lead R Thermal Resistance Junction-ambient thj-amb R Thermal Resistance Junction-ambient (two chips ON) thj-amb (1) When mounted on a standard single-sided FR-4 board with 0.5cm mounting and no ...
Page 5
ELECTRICAL CHARACTERISTICS (continued OUTPUT DIODE CC Symbol Parameter V Forward on Voltage F STATUS PIN (Per each channel) Symbol Parameter V Status Low Output Voltage I STAT I Status Leakage Current LSTAT Status Pin Input C STAT Capacitance ...
Page 6
VNQ830M Switching time Waveforms V OUTn 80% dV /dt OUT (on) V INn t d(on) TRUTH TABLE CONDITIONS Normal Operation Current Limitation Overtemperature Undervoltage Overvoltage Output Voltage > Output Current < 6/21 10% t d(off) INPUT ...
Page 7
ELECTRICAL TRANSIENT REQUIREMENTS ON V ISO T/R 7637/1 Test Pulse +26.5 V ISO T/R 7637/1 Test Pulse ...
Page 8
VNQ830M Figure 1: Waveforms INPUT n LOAD VOLTAGE n STATUS INPUT n LOAD VOLTAGE n STATUS V CC INPUT n LOAD VOLTAGE n STATUS n INPUT n LOAD VOLTAGE n STATUS n INPUT n LOAD VOLTAGE n ...
Page 9
APPLICATION SCHEMATIC +5V +5V +5V R prot R prot R prot R prot C R prot R prot R prot R prot +5V +5V Note: Channels 3 & 4 have the same internal circuit as channel 1 & 2. GND ...
Page 10
VNQ830M Solution 2: A diode ( the ground line. GND A resistor (R =1k should be inserted in parallel to GND D if the device will be driving an inductive load. GND This small signal diode can be ...
Page 11
OPEN LOAD DETECTION IN OFF STATE Off state open load detection requires an external pull-up resistor (R ) connected between OUTPUT pin and a PU positive supply voltage (V ) like the +5V line used to PU supply the microprocessor. ...
Page 12
VNQ830M Off State Output Current IL(off1) (uA) 2.5 2.25 Off state 2 Vcc=36V Vin=Vout=0V 1.75 1.5 1.25 1 0.75 0.5 0.25 0 -50 - (°C) Input Clamp Voltage Vicl (V) 8 7.8 Iin=1mA 7.6 7.4 ...
Page 13
On State Resistance Vs T case Ron (mOhm) 160 140 Iout=2A Vcc=8V; 13V & 36V 120 100 -50 - (°C) Openload On State Detection Threshold Iol (mA) 1250 1200 Vcc=13V ...
Page 14
VNQ830M Overvoltage Shutdown Vov ( -50 - (°C) Turn-on Voltage Slope dVout/dt(on) (V/ms) 800 700 Vcc=13V Rl=6.5Ohm 600 500 400 300 200 100 0 ...
Page 15
Maximum turn off current versus load inductance I LMAX (A) 100 Single Pulse at T =150ºC Jstart B= Repetitive pulse at T =100ºC Jstart C= Repetitive Pulse at T =125ºC Jstart Conditions: V =13.5V CC ...
Page 16
VNQ830M SO-28 DOUBLE ISLAND THERMAL DATA SO-28 Double island PC Board Layout condition of R and thickness=35 m, Copper areas: 0.5cm Thermal calculation according to the PCB heatsink area Chip 1 Chip 2 ON OFF R x ...
Page 17
SO-28 Thermal Impedance Junction Ambient Single Pulse Zth(°C/W ) 100 10 1 0.1 0.01 1E-04 0.001 0.01 Thermal fitting model of a four channels HSD in SO-28 Tj_1 Pd1 C13 C14 Tj_2 ...
Page 18
VNQ830M DIM. MIN 0.10 b 0. 17.7 E 10. 7.40 L 0.40 S 18/21 SO-28 MECHANICAL DATA mm. TYP MAX. 2.65 0.30 0.49 0.32 0.50 45 (typ.) 18.1 10.65 1.27 ...
Page 19
TAPE AND REEL SHIPMENT (suffix “13TR”) TAPE DIMENSIONS According to Electronic Industries Association (EIA) Standard 481 rev. A, Feb 1986 Tape width W Tape Hole Spacing P0 (± 0.1) Component Spacing P Hole Diameter D (± 0.1/-0) ...
Page 20
VNQ830M REVISION HISTORY Date Revision - Current and voltage convention update (page 3). - “Configuration diagram (top view) & suggested connections for unused and n.c. pins” insertion (page 3 6cm July 2004 1 - PROTECTIONS note insertion (page ...
Page 21
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. ...