HIP6601A INTERSIL [Intersil Corporation], HIP6601A Datasheet
HIP6601A
Available stocks
Related parts for HIP6601A
HIP6601A Summary of contents
Page 1
... ISL65xx Multi-Phase Buck PWM controller form a complete core-voltage regulator solution for advanced microprocessors. The HIP6601A drives the lower gate in a synchronous rectifier to 12V, while the upper gate can be independently driven over a range from 5V to 12V. The HIP6603A drives both upper and lower gates over a range 12V. This ...
Page 2
... SHOOT- THROUGH PROTECTION LVCC LGATE PGND PAD PAD ON THE BOTTOM SIDE OF THE PACKAGE MUST BE SOLDERED TO THE PC BOARD BOOT UGATE † VCC FOR HIP6601A PHASE PVCC FOR HIP6603A LGATE GND CONNECT LVCC TO VCC FOR HIP6601A CONFIGURATION CONNECT LVCC TO PVCC FOR HIP6603A CONFIGURATION. ...
Page 3
... Typical Application - 3 Channel Converter Using HIP6301 and HIP6601A Gate Drivers +5V VFB COMP VCC PWM1 VSEN PWM2 PWM3 PGOOD MAIN CONTROL HIP6301 VID ISEN1 ISEN2 FS ISEN3 GND 3 HIP6601A, HIP6603A, HIP6604 +5V BOOT PVCC UGATE VCC PHASE DRIVE PWM HIP6601A LGATE +5V BOOT PVCC UGATE ...
Page 4
... Load PDLLGATE PVCC UGATE PVCC V = 12V PVCC UGATE PVCC V = 12V PVCC 5V, HIP6603A LGATE PVCC V = 12V, HIP6603A PVCC 12V, HIP6601A PVCC 12V LGATE PVCC o θ C/W) θ MIN TYP MAX = 12V - 4.4 6.2 PVCC = 12V - 2.5 3.6 PVCC ...
Page 5
... PDLLGATE 5 HIP6601A, HIP6603A, HIP6604 PVCC (Pin 7), (Pin 11 QFN) For the HIP6601A and the HIP6604, this pin supplies the upper gate drive bias. Connect this pin from +12V down to +5V. For the HIP6603A, this pin supplies both the upper and lower gate drive bias. Connect this pin to either +12V or +5V. ...
Page 6
... GND peak ringing below 17V. Gate Drive Voltage Versatility The HIP6601A and HIP6603A provide the user total flexibility in choosing the gate drive voltage. The HIP6601A lower gate drive is fixed to VCC [+12V], but the upper drive rail can range from 12V down to 5V depending on what voltage is applied to PVCC ...
Page 7
... Figure 2 shows the dissipation in the driver with 3nF loading on both gates and each individually. Note the higher upper gate power dissipation which is due to the bootstrap device refresh cycle. Again PVCC and VCC are tied together and to a +12V supply. 7 HIP6601A, HIP6603A, HIP6604 Test Circuit +12V U U 1000 ...
Page 8
... Since both upper and lower gate capacitance can vary, Figure 8 shows dissipation curves versus lower gate capacitance with upper gate capacitance held constant at three different values. These curves apply only to the HIP6601A due to power supply configuration. Typical Performance Curves 1000 VCC = PVCC = 12V ...
Page 9
... A D -C- α µ 0.10(0.004) 0.25(0.010 SIDE VIEW BOTTOM VIEW 9 HIP6601A, HIP6603A, HIP6604 M8.15B 8 LEAD NARROW BODY SMALL OUTLINE EXPOSED PAD PLASTIC PACKAGE SYMBOL α ...
Page 10
... Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP) 10 HIP6601A, HIP6603A, HIP6604 L16.4x4 16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220-VGGC ISSUE C) SYMBOL θ NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. ...
Page 11
... Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com 11 HIP6601A, HIP6603A, HIP6604 M8.15 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC M ...