HIP4086AABZ INTERSIL [Intersil Corporation], HIP4086AABZ Datasheet
HIP4086AABZ
Available stocks
Related parts for HIP4086AABZ
HIP4086AABZ Summary of contents
Page 1
MOSFET Driver HIP4086, HIP4086A The HIP4086 and HIP4086A (referred to as the HIP4086/A) are three phase N-Channel MOSFET drivers. Both parts are specifically targeted for PWM motor control. These drivers have flexible input protocol for driving every ...
Page 2
Block Diagram (for clarity, only one phase is shown) If under voltage is active or if DIS is asserted, the high and low-side drivers are turned off. xHI 5 DIS 10 VDD 20 Under Voltage Detector UVLO 8 Refresh RFSH ...
Page 3
Pin Configuration Pin Descriptions PIN NUMBER SYMBOL 16 AHB 1 BHB 13 CHB (xHB) 15 AHS 23 BHS 15 CHS (xHS) 5 AHI 2 BHI 12 CHI (xHI) 4 ALI 3 BLI 11 CLI (xLI RDEL ...
Page 4
... HIP4086AB HIP4086AB HIP4086ABZ (Note 2) HIP4086ABZ HIP4086APZ (Note 2) HIP4086APZ HIP4086AABZ (Note 2) HIP4086AABZ HIP4086EVAL Evaluation Board NOTES: 1. Add “-T*”, suffix for tape and reel. Please refer to 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations) ...
Page 5
... Falling Undervoltage Threshold Minimum Undervoltage Threshold HIP4086, HIP4086A Thermal Information Thermal Resistance (Typical) SOIC Package (Notes 0.3V SOIC Package HIP4086AABZ (Notes +150 C) ° ° PDIP* Package (Notes 0. xHS xHS DD Storage Temperature Range .-65°C to +150° ...
Page 6
DC Electrical Specifications unless otherwise specified. Boldface limits apply over the operating junction temperature range, -40°C to +150°C. PARAMETER INPUT PINS: ALI, BLI, CLI, AHI, BHI, CHI, AND DIS Low Level Input Voltage High Level Input Voltage Input Voltage Hysteresis ...
Page 7
Test Waveforms and Timing Diagrams xLI to xLO turn-off xLI xHI xLO xHO xHI to xHO turn-on + delay FIGURE 3. PROP DELAYS WITH PROGRAMMED TURN-ON DELAYS (RDEL CONNECTED TO VDD WITH A RESISTOR) xLI to xLO turn-off xLI xHI ...
Page 8
Typical Performance Curves 6 ALL GATE CONTROL INPUTS = 16V 15V 12V 10V -60 -40 ...
Page 9
Typical Performance Curves 1 0 15V DD 0 12V 10V DD 0 0.2 0 -60 -40 - JUNCTION TEMPERATURE (°C) FIGURE ...
Page 10
Typical Performance Curves 6 RDEL = 100kΩ RDEL = 10kΩ 0 -60 -40 - JUNCTION TEMPERATURE (°C) FIGURE 18. DEAD TIME Functional Description Input Logic NOTE: When appropriate for brevity, input and output pins ...
Page 11
Charge Pump The internal charge pump of the HIP4086/A is used to maintain the bias on the boot cap for 100% duty cycle. There is no limit for the duration of this period. The user must understand that this charge ...
Page 12
Typical Application Circuit Speed Controller Brake Figure example of how the HIP4086 and HIP4086A 3-phase drivers can be applied to drive a 3-phase motor. Depending on the application, the switching speed of the bridge FETs can be ...
Page 13
General PCB Layout Guidelines The AC performance of the HIP4086/A depends significantly on the design of the PC board. The following layout design guidelines are recommended to achieve optimum performance: • Place the driver as close as possible to the ...
Page 14
... Title from "80V, 500mA, 3-Phase Driver" to "80V, 500mA, 3-Phase MOSFET Driver" -Rewrote description on page 1 by adding HIP4086A and stating the differences between parts. -Updated ordering information by adding part number HIP4086AABZ and EVAL Board. Added MSL note and numbered all notes to meet new standard, Removed obsolete part HIP4086AP ...
Page 15
Dual-In-Line Plastic Packages (PDIP INDEX N/2 AREA -B- -A- D BASE PLANE -C- SEATING PLANE 0.010 (0.25 NOTES: 1. Controlling Dimensions: INCH. In case of conflict between ...
Page 16
Package Outline Drawing M24.3 24 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE (SOIC) Rev 2, 3/11 24 INDEX AREA TOP VIEW 15.60 (0.614) 15.20 (0.598) 1.27 (0.050) 0.51 (0.020) 0.33 (0.013) SIDE VIEW “A” 1.981 (0.078) 1.27 ...