KSZ8041NLJ_10 MICREL [Micrel Semiconductor], KSZ8041NLJ_10 Datasheet - Page 7

• Manufacturer Part Number: KSZ8041NLJ_10
• Description: 10/100 Ethernet Transceiver with Extended Temperature Support
• Manufacturer: MICREL [Micrel Semiconductor]

Micrel, Inc.
Pin Description
April 2010
Pin Number
10
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
VDDPLL_1.8
VDDIO_3.3
VDDA_3.3
Pin Name
CONFIG2
PHYAD0
PHYAD1
PHYAD2
DUPLEX
CRSDV /
REFCLK
RXD[1] /
RXD[0] /
RXDV /
RXD3 /
RXD2 /
RXD1 /
RXD0 /
REXT
MDIO
GND
MDC
RXC
RX+
TX+
RX-
TX-
XO
XI /
Type
Ipu/O
Ipd/O
Ipd/O
Ipu/O
Ipd/O
GND
I/O
I/O
I/O
I/O
I/O
I/O
P
P
O
P
O
I
I
(1)
Pin Function
Ground
1.8V analog V
3.3V analog V
Physical receive or transmit signal (- differential)
Physical receive or transmit signal (+ differential)
Physical transmit or receive signal (- differential)
Physical transmit or receive signal (+ differential)
Crystal feedback
This pin is used only in MII mode when a 25MHz crystal is used.
This pin is a no connect if oscillator or external clock source is used, or if RMII mode
is selected.
Crystal / Oscillator / External Clock Input
MII Mode:
RMII Mode:
Set physical transmit output current
Connect a 6.49KΩ resistor in parallel with a 100pF capacitor to ground on this pin.
Management Interface (MII) Data I/O
This pin requires an external 4.7KΩ pull-up resistor.
Management Interface (MII) Clock Input
This pin is synchronous to the MDIO data interface.
MII Mode:
Config Mode:
MII Mode:
Config Mode:
MII Mode:
RMII Mode:
Config Mode:
MII Mode:
RMII Mode:
Config Mode:
3.3V digital V
MII Mode:
RMII Mode:
Config Mode:
MII Mode:
DD
DD
DD
25MHz +/-50ppm (crystal, oscillator, or external clock)
50MHz +/-50ppm (oscillator, or external clock only)
Receive Data Output[3]
Receive Data Output[2]
Receive Data Output[1]
Receive Data Output[1]
Receive Data Output[0]
Receive Data Output[0]
Receive Data Valid Output /
Carrier Sense/Receive Data Valid Output /
Receive Clock Output
The pull-up/pull-down value is latched as PHYADDR[0] during
power-up / reset. See “Strapping Options” section for details.
The pull-up/pull-down value is latched as PHYADDR[1] during
power-up / reset. See “Strapping Options” section for details.
The pull-up/pull-down value is latched as PHYADDR[2] during
power-up / reset. See “Strapping Options” section for details.
Latched as DUPLEX (register 0h, bit 8) during power-up /
reset. See “Strapping Options” section for details.
The pull-up/pull-down value is latched as CONFIG2 during
power-up / reset. See “Strapping Options” section for details.
7
(2)
(2)
(2)
(3)
(2)
(3)
/
/
/
/
/
/
M9999-040110-1.0
KSZ8041NLJ