dtr-156-sm2-lc-ls-w OPLINK Communications Inc., dtr-156-sm2-lc-ls-w Datasheet
dtr-156-sm2-lc-ls-w
Related parts for dtr-156-sm2-lc-ls-w
dtr-156-sm2-lc-ls-w Summary of contents
Page 1
... OCP DTR-xxx-SM2-LC/LS-W OC-3/STM-1 & OC-12/STM-4 SFF Single Mode Transceivers Description The DTR-xxx-SM2-LC-W and DTR-xxx-SM2-LS-W series of fiber optic transceivers provide a quick and reliable interface for short reach (SR), intermediate reach (IR) and long reach (LR) applications. Available products under this series are compliant with SONET/SDH standards for OC-3/ STM-1 and OC-12/STM-4 ...
Page 2
... OC-3/STM-1 Single Mode Transceivers: DTR-156-SM2-LC/LS-W Transmitter Performance Characteristics All parameters guaranteed only at typical data rate Parameter 1 Operating Data Rate Average Optical Output Power (coupled into single mode fiber), 50% duty cycle Extinction Ratio Center Wavelength Spectral Width (RMS) Spectral Width (-20dB) Side Mode Suppression Ratio ...
Page 3
... OC-12/STM-4 Single Mode Transceivers: DTR-622-SM2-LC/LS-W Transmitter Performance Characteristics All parameters guaranteed only at typical data rate Parameter 1 Operating Data Rate Average Optical Output Power (coupled into single mode fiber), 50% duty cycle Extinction Ratio 2 Center Wavelength 2 Spectral Width (RMS) Spectral Width (-20dB) Side Mode Suppression Ratio ...
Page 4
... DTR-xxx-SM2-LC-W & DTR-xxx-SM2-LS-W Transmitter Electrical Interface Parameter Input HIGH Voltage Input LOW Voltage Data Input Current - HIGH Data Input Current - LOW Transmitter Disable Voltage Transmitter Enable Voltage Differential Bias Monitor Voltage (T = 25°C) a Differential Back Facet Monitor Voltage Receiver Electrical Interface ...
Page 5
... DTR-xxx-SM2-LC-W & DTR-xxx-SM2-LS-W Interface circuit (DC-coupling) VCC +3.3V µ coil or ferrite inductor 0.1 µ coil or ferrite inductor + 10 TX Disable SIGNAL DETECT (see Note below) VPD +3.3V 100 + 10 circuit ground Note: If signal detect is LV-PECL, a termination resistor of 160 Interface circuit (DC-coupling) VCC +3.3V µ coil or ferrite inductor 0 ...
Page 6
... DTR-xxx-SM2-LC-W & DTR-xxx-SM2-LS-W Interface circuit (AC-coupling) VCC +3.3V µ coil or ferrite inductor 0.1 µ coil or ferrite inductor + 10 TX Disable SIGNAL DETECT (see Note below) VPD +3.3V 100 + 0.1 10 circuit ground Note: If signal detect is LV-PECL, a termination resistor of 160 Application Notes Transmitter: When the DATA+ input is at logic HIGH and DATA- input is at logic LOW, the laser diode is ON, and vice versa ...
Page 7
... DTR-xxx-SM2-LC-W & DTR-xxx-SM2-LS-W Package without EMI Shield (LC) [13.56 MAX] .535 MAX [9.78 MAX] .385 MAX 0.38 .015 TYP (X)* 0.25 2x .010 PIN 11 10.16 .400 1.91 2X .075 PIN 10 1.78 [0.46] .070 TYP .018 Package with EMI Shield (LS) [13.56 MAX] .535 MAX [9.78 MAX] .385 MAX 0.38 .015 TYP (X)* 0.25 2X .010 PIN 11 10.16 .400 1.91 2X .075 PIN 10 1 ...
Page 8
... DTR-xxx-SM2-LC-W & DTR-xxx-SM2-LS-W Package with S1 EMI Shield (S1) [13.56 MAX] .535 MAX [9.78 MAX] .385 MAX 0.38 .015 TYP (X)* PIN 11 10.16 .400 1.91 .075 PIN 10 1.78 [0.46] .070 TYP 0.18 TYP 48.39 1.905 15.11 .60 15.01 .59 (Y)* 2.54 1.02 2X .100 2X .040 [13.59 +0/-0.254] .535 +0/-.01 PIN 1 8.89 18.54 .350 .730 8 14.09 .555 6.25 3.6 .246 .14 9.65 11.9 .38 .47 (X)* & (Y)*: see Pin Length 15 ...
Page 9
... LR1 : LR-1/L-1.1 (50/40km) LR2 : LR-2/L-1.2 (100/80km) NOTE: 1. These are target distances to be used for classification and not for specification, per Telcordia GR-253-CORE/ITU-T Recommendation G.957 Ordering Information for OC-12/STM-4 DTR - 622 - SM2 - Lx - Wpy - S1 Connector LC : w/o EMI Shield Temperature Range EMI Shield “Blank” : -5°C to +70°C “ ...