mt8920bs1 Zarlink Semiconductor, mt8920bs1 Datasheet - Page 8

• Manufacturer Part Number: mt8920bs1
• Description: 32 Channels Tdm St-bus To Parallel Bus Access Circuit
• Manufacturer: Zarlink Semiconductor

MT8920B
8
Timing information for data transfers on this interface
is shown in Figure 14.
designed to operate directly with a 68000-type
asynchronous bus but can easily accommodate most
other popular microprocessors as well.
Control Registers
Two control registers allow control of Mode 1
features. Control Register 1 provides bits to select
the type of interrupt, to enable interrupts from two
different and independent sources and to reset the
interrupt registers.
Register 1 are bits to configure the device for 24 or
32 channel operation and to expand the address
range for convenient access to the second transmit
RAM Tx1.
Control Register 1 is shown in Table 3.
Mode 1 provides various loopback paths and output
configuration options which are controlled by bits in
Control Register 2. Bits D
configure loopbacks using input and output streams
STi0, STo0 as described in Table 4.
stream STi0 can be looped back to source the output
stream STo0 as well as receive RAM Rx0. The
transmit RAM Tx0 can be looped to source the
receive RAM Rx0, as well as STo0 and, the transmit
RAM Tx0 can be looped to the receive RAM Rx0
while STi0 sources STo0.
loopback configurations is shown in Figure 5.
In a similar way, the output STo1 can be reconfigured
for different functionality. Bits D
Register 2 allow STo1 to be sourced, with a one
frame delay via Tx1 from receive stream STi0. STo1
can also output the result of a comparison of the
contents of Tx1 ram with input stream STi0. These
output configurations of STo1 are shown in Figure 6
7-4
3-2
1-0
Bit
LOOPBACK Internal Loopback Configuration Bits:
(Unused)
CONFIG
Name
A description of the bit functions in
Also contained in Control
STo1 Output Configuration Bits:
D
D
3
1
D
D
0
The Mode 1 interface is
, D
2
0
= 00-
The function of these
= 00-
1
01-
10-
11-
01-
10-
11-
of Control Register 2
2
and D
Table 4. Control Register 2 Bit Definitions
Normal operation. ST-BUS stream from Tx1 is output on STo1 pin.
STi0 stream is output on STo1 pin delayed one frame (Figure 6 a).
STi0 is compared through XOR (exclusive OR) with ST-BUS stream
STi0 stream, delayed one frame (via Tx1), is compared (XOR) with the
Normal operation. No internal loops.
Loop STi0 to STo0 while still receiving STi0 in Rx0 (Figure 5 a).
Loop Tx0 output ST-BUS stream to Rx0 input ST-BUS stream while
Loop Tx0 output ST-BUS stream to Rx0 input ST-BUS stream. Loop
from Tx1 and output at STo1 (Figure 6 b).
next frame arriving at STi0 and the result output at STo1 (Figure 6 c).
outputting Tx0 output to STo0. STi0 is not received (Figure 5 b).
STi0 to STo0 (Figure 5 c).
3
The input
of Control
a and b.
these two features.
Interrupt Registers
Interrupts can be generated in Mode 1 only. Two
channels of the ST-BUS input stream, STi0, can be
selected to provide an interrupt to the system.
Interrupts can be of two types: Static or Dynamic.
Static interrupts are caused when data within a
selected channel matches a given pattern. Dynamic
interrupts occur when bits in a selected channel
change state (1 to 0, 0 to 1 or toggle). Interrupts are
controlled through two identical paths (1 and 2)
consisting of the following registers:
Interrupt Channel Address (1/2):
(0-31) of the channel which will generate the
interrupt is stored in this register.
Image Register (1/2):
channel causing the interrupt is stored in this
register. Reading this register will clear its contents.
Match Byte Register (1/2):
register is used to store the byte which will be
compared with the contents of the selected channel
causing the interrupt.
In dynamic mode, the bits in this register and the
corresponding bit in the Interrupt Mask Register
define the type of dynamic interrupt (i.e., 0 to 1, 1 to
0, toggle). (Refer to Table 5.)
Description
Figure 6 c shows the effect of combining
The
In static mode this
contents
Data Sheet
The address
of
the