ncp5389 ON Semiconductor, ncp5389 Datasheet - Page 18

• Manufacturer Part Number: ncp5389
• Description: 2/3 Phase Buck Controller For Vr11 Pentium Iv Processor Applications
• Manufacturer: ON Semiconductor

General
controller is specifically designed with the necessary
features for a high current VR11 CPU power system. The
IC
Programmable DAC, Differential Remote Voltage Sense
Amplifier, High Performance Voltage Error Amplifier,
Differential Current Feedback Amplifiers, Precision
Oscillator and Triangle Wave Generators, and PWM
Comparators. Protection features include Undervoltage
Lockout, Soft-Start, Overcurrent Protection, Overvoltage
Protection, and Power Good Monitor.
Remote Output Sensing Amplifier (RSA)
measure Vcore voltage feedback with respect to the Vcore
ground reference point by connecting the Vcore reference
point to VS+, and the Vcore ground reference point to VS-.
This configuration keeps ground potential differences
between the local controller ground and the Vcore ground
reference point from affecting regulation of Vcore between
Vcore and Vcore ground reference points. The RSA also
subtracts the DAC (minus VID offset) voltage, thereby
producing an unamplified output error voltage at the
DIFFOUT pin. This output also has a 1.3 V bias voltage to
allow both positive and negative error voltages.
Precision DAC
has 0.75% accuracy over the entire operating temperature
range of the part.
High Performance Voltage Error Amplifier
and bandwidth. Although not required when operating as
a voltage regulator, a capacitor from COMP to VFB is
required for stable unity gain test configurations.
Gate Driver Outputs and 2/3 Phase Operation
In 2-phase mode, phases 1 and 3 should be used to drive the
external gate drivers as shown in the 2-phase Applications
Schematic. In 2-phase mode, gate output G2 must be
grounded as shown in the 2-phase Applications Schematic.
The following truth table summarizes the modes of
operation:
The NCP5389 dual edge modulated multiphase PWM
A true differential amplifier allows the NCP5389 to
A precision programmable DAC is provided. This DAC
The error amplifier is designed to provide high slew rate
The part can be configured to run in 2- or 3-phase mode.
consists
FUNCTIONAL DESCRIPTION
of
the
following
blocks:
Precision
http://onsemi.com
NCP5389
18
program the modes of operation.
Differential Current Sense Amplifiers
output current of each phase. The inputs of each current
sense amplifier must be connected across the current
sensing element of the phase controlled by the
corresponding gate output (G1, G2 or G3). If 2 phase is
unused, the differential inputs to that phase's current
sense amplifier must be shorted together and connected
to V
Schematics.
(such as an inductor or sense resistor) by the current
flowing in that phase. The output of the current sense
amplifiers are used to control three functions. First, the
output controls the adaptive voltage positioning, where the
output voltage is actively controlled according to the
output current. In this function, all of the current sense
outputs are summed so that the total output current is used
for output voltage positioning. Second, the output signal is
fed to the current limit circuit. This again is the summed
current of all phases in operation. Finally, the individual
phase current is connected to the PWM comparator. In this
way current balance is accomplished.
Oscillator and Triangle Wave Generator
oscillator 's frequency is programmed by the resistance
connected from the ROSC pin to ground. The user will
usually form this resistance from two resistors in order to
create a voltage divider that uses the ROSC output voltage
as the reference for creating the current limit setpoint
voltage. The oscillator frequency range is 100 kHz/phase
to 1.0 MHz/phase. The oscillator generates up to 3 triangle
waveforms (symmetrical rising and falling slopes)
between 1.3 V and 2.3 V. The triangle waves have a phase
delay between them such that for 2-, 3-phase operation the
PWM outputs are separated by 180 and 120 angular
degrees, respectively.
These are the only allowable connection schemes to
Three differential amplifiers are provided to sense the
A voltage is generated across the current sense element
A programmable precision oscillator is provided. The
2-Phase
3-Phase
Mode
CCP
as shown in the 2-phase Application
Normal
Normal
G1
Gate Output Connections
Normal
GND
G2
Normal
Normal
G3