bu6520kv ROHM Co. Ltd., bu6520kv Datasheet
bu6520kv
Available stocks
Related parts for bu6520kv
bu6520kv Summary of contents
Page 1
... DAC 1ch (output load R=75Ω) The registers in BU6520KV from the outside can be set The registers setting value can be stored in external EEPROM When reset is released or the mode is changed, the setting of the registers in BU6520KV can be automatically set Compatible with 4 power sources(VDD=1.50V, VDDIO=3.30V, VDDI ...
Page 2
Parameter Symbol Applied power VDDIO1 source voltage 1 Applied power 2 VDDI C source voltage 2 Applied power AVDD source voltage 3 Applied power VDD source voltage 4 VIN -0.3～IO_LVL+0.3*1 Input voltage Storage Tstg temperature range Power ...
Page 3
... Serial Interface for EEPROM (SPI) SDI SDO SCK SCEB WPB 1.5V 3.3V 3.3V 3.3V VDD VDDIO VDDI2C ADDD CAMDO [7:0] ] CAMDI [7:0 CAMHSI CAMVSI CAMCKI SDA SDC BU6520KV RESETB SCEB SCK SDO SDI WPB AUTO MODE 0 MODE1 GND AVSS 3/12 8 CAMDO[7:0] YUV=4:2:2 10bit VOUT DAC IREF CAMHSO CAMVSO ...
Page 4
PIN PIN No. In/Out Name 1 SDI In 2 CAMDI7 In 3 CAMDI6 In 4 CAMDI5 In 5 CAMDI4 In 6 GND 7 VDD 8 CAMDI3 In 9 CAMDI2 In 10 CAMDI1 In 11 CAMDI0 In 12 CAMHSI ...
Page 5
PIN Active PIN No. In/Out Name Level 25 CAMHSO Out * 26 CAMVSO Out * 27 CAMCKO Out CLK 28 GND - GND 29 VDD - PWR 30 AUTO In High 31 MODE0 In DATA 32 MODE1 In DATA 33 ...
Page 6
Circuit Structures of input / output pins Type Equivalent circuit configuration VDDIO A Input terminal GND Internal signal VDDIO C GND Input terminal with suspend VDDIO E GND Input terminal with schmitt and suspend VDDIO To internal GND G ...
Page 7
Layout （Bottom View） SDI CAMDI7 CAMDI6 CAMDI5 CAMDI4 GND VDD CAMDI3 CAMDI2 CAMDI1 CAMDI0 CAMHSI ●Timing Chart 1. Date input / output interface Data input interface timing CAMVSI CAMHSI CAMDI[7:0] CAMCKI (CKPOL=“1”) CAMCKI (CKPOL=“0”) t CMS Data output interface ...
Page 8
... When the automatic reading function with the AUTO pin is used, it becomes timing of SCEB to SCK as above possible to access from the register of BU6520KV to interface.In that case, SCEB is controlled by the register. After the value is set to the register, the SCEB pin is changed into the logic set at once. ...
Page 9
Output waveform in NTSC VOU T 0.0 IRE -40.0 IRE (Note) (*1) The white level and the black level can be changed by the setting. 4. Output waveform in PAL VOU T 0.0 IRE -43.0 IRE (Note) (*1) The ...
Page 10
I C BUS Format Slave address is 70h. The subaddress increment automatically when continuously accessing(read / write times or more. SDI SCLK S 1-7 8 START Slave R/W condition address Write Slave address W S A(S) ...
Page 11
Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or ...
Page 12
Model Name Selection ROHM model name Product number ●Tape and Reel information VQFP48C <Dimension> 9.0±0.2 7.0±0 +0.05 0.75 0.145 −0.03 ° +6° 4 −4° 0.08 S 0.5±0.1 ...
Page 13
Appendix No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product ...