sc2-n0-ye Pepperl+Fuchs, sc2-n0-ye Datasheet - Page 6

• Manufacturer Part Number: sc2-n0-ye
• Description: Inductive Slot Sensor
• Manufacturer: Pepperl+Fuchs

6
ATEX 3G (ic)
Instruction
Device category 3G (ic)
Directive conformity
Standard conformity
CE symbol
Ex-identification
Effective internal capacitance C
Effective internal inductance L
General
Installation, Comissioning
Maintenance
Special conditions
Maximum permissible ambient temperature T
Protection from mechanical danger
Connection parts
Inductive slot sensor
for Pi=34 mW, Ii=25 mA, T6
for Pi=34 mW, Ii=25 mA, T5
for Pi=34 mW, Ii=25 mA, T4-T1
for Pi=64 mW, Ii=25 mA, T6
for Pi=64 mW, Ii=25 mA, T5
for Pi=64 mW, Ii=25 mA, T4-T1
for Pi=169 mW, Ii=52 mA, T6
for Pi=169 mW, Ii=52 mA, T5
for Pi=169 mW, Ii=52 mA, T4-T1
for Pi=242 mW, Ii=76 mA, T6
for Pi=242 mW, Ii=76 mA, T5
for Pi=242 mW, Ii=76 mA, T4-T1
Subject to modifications without notice
Pepperl+Fuchs Group
www.pepperl-fuchs.com
i
i
[e-mail]
USA: [phone]
Umax
at Ui = 20 V
Germany: [phone]
[e-mail]
Manual electrical apparatus for hazardous areas
for use in hazardous areas with gas, vapour and mist
94/9/EG
EN 60079-11:2007 Ignition protection category "ic"
Use is restricted to the following stated conditions
¬ II 3G Ex ic IIC T6 X The Ex-significant identification is on the enclosed adhesive
label
≤ 150 nF ; a cable length of 10 m is considered.
≤ 150 µH ; a cable length of 10 m is considered.
The apparatus has to be operated according to the appropriate data in the data
sheet and in this instruction manual. The data stated in the data sheet are restricted
by this operating instruction!
The special conditions must be observed!
Directive 94/9EG is generally applicable only to the use of electrical apparatus ope-
rating at atmospheric conditions.
If the equipment is not used under atmospheric conditions, a reduction of the per-
missible minimum ignition energies may have to be taken into consideration.
Laws and/or regulations and standards governing the use or intended usage goal
must be observed. The sensor must only be operated with energy-limited circuits,
which satisfy the requirements of IEC 60079-11. The explosion group complies with
the connected, supplying, power limiting circuit. The adhesive label provided must
be affixed in the immediate vicinity of the sensor! The surface to which the label is
applied must be clean, flat and free from grease!
The affixed adhesive label must be readable and durable, taking account of the
possibility of chemical corrosion!
No changes can be made to apparatus, which are operated in hazardous areas.
Repairs to these apparatus are not possible.
66 °C (150.8 °F)
81 °C (177.8 °F)
100 °C (212 °F)
65 °C (149 °F)
80 °C (176 °F)
100 °C (212 °F)
40 °C (104 °F)
55 °C (131 °F)
75 °C (167 °F)
23 °C (73.4 °F)
38 °C (100.4 °F)
54 °C (129.2 °F)
The sensor must not be mechanically damaged.
When used in the temperature range below -20 °C the sensor should be protected
from knocks by the provision of an additional housing.
The connection parts are to be installed, such that a minimum protection class of
IP20 is achieved, in accordance with IEC 60529.
0102
[e-mail]
Singapore: [phone]
Copyright Pepperl+Fuchs
SC2-N0-YE