sc2-n0-ye Pepperl+Fuchs, sc2-n0-ye Datasheet - Page 5

• Manufacturer Part Number: sc2-n0-ye
• Description: Inductive Slot Sensor
• Manufacturer: Pepperl+Fuchs

Subject to modifications without notice
Pepperl+Fuchs Group
www.pepperl-fuchs.com
ATEX 3G (nL)
Note
Instruction
Device category 3G (nL)
Directive conformity
Standard conformity
CE symbol
Ex-identification
Effective internal capacitance C
Effective internal inductance L
General
Installation, Comissioning
Maintenance
Special conditions
Maximum permissible ambient temperature T
Protection from mechanical danger
Connection parts
Inductive slot sensor
for Pi=34 mW, Ii=25 mA, T6
for Pi=34 mW, Ii=25 mA, T5
for Pi=34 mW, Ii=25 mA, T4-T1
for Pi=64 mW, Ii=25 mA, T6
for Pi=64 mW, Ii=25 mA, T5
for Pi=64 mW, Ii=25 mA, T4-T1
for Pi=169 mW, Ii=52 mA, T6
for Pi=169 mW, Ii=52 mA, T5
for Pi=169 mW, Ii=52 mA, T4-T1
for Pi=242 mW, Ii=76 mA, T6
for Pi=242 mW, Ii=76 mA, T5
for Pi=242 mW, Ii=76 mA, T4-T1
[e-mail]
USA: [phone]
i
i
Umax
Germany: [phone]
at Ui = 20 V
[e-mail]
This instruction is only valid for products according to EN 60079-15:2003, valid until
31-May-2008
Manual electrical apparatus for hazardous areas
for use in hazardous areas with gas, vapour and mist
94/9/EG
EN 60079-15:2003 Ignition protection category "n"
Use is restricted to the following stated conditions
¬ II 3G EEx nL IIC T6 X The Ex-significant identification is on the enclosed adhe-
sive label
≤ 150 nF ; a cable length of 10 m is considered.
≤ 150 µH ; a cable length of 10 m is considered.
The apparatus has to be operated according to the appropriate data in the data
sheet and in this instruction manual. The data stated in the data sheet are restric-
ted by this operating instruction! The special conditions must be observed!
Laws and/or regulations and standards governing the use or intended usage goal
must be observed. The sensor must only be operated with an energy-limited circuit,
which satisfies the requirements of IEC 60079-15. The explosion group complies
with the connected, supplying, power limiting circuit. The adhesive label provided
must be affixed in the immediate vicinity of the sensor! The surface to which the
label is applied must be clean, flat and free from grease!
The affixed adhesive label must be readable and durable, taking account of the
possibility of chemical corrosion!
No changes can be made to apparatus, which are operated in hazardous areas.
Repairs to these apparatus are not possible.
66 °C (150.8 °F)
81 °C (177.8 °F)
100 °C (212 °F)
65 °C (149 °F)
80 °C (176 °F)
100 °C (212 °F)
40 °C (104 °F)
55 °C (131 °F)
75 °C (167 °F)
23 °C (73.4 °F)
38 °C (100.4 °F)
54 °C (129.2 °F)
The sensor must not be mechanically damaged.
When used in the temperature range below -20 °C the sensor should be protected
from knocks by the provision of an additional housing.
The connection parts are to be installed, such that a minimum protection class of
IP20 is achieved, in accordance with IEC 60529.
[e-mail]
0102
Singapore: [phone]
Copyright Pepperl+Fuchs
SC2-N0-YE
5