MX29LV800AB Macronix, MX29LV800AB Datasheet - Page 14

no-image

MX29LV800AB

Manufacturer Part Number
MX29LV800AB
Description
8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
Manufacturer
Macronix
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MX29LV800ABTC-70
Manufacturer:
MOLEX
Quantity:
5 000
Part Number:
MX29LV800ABTC-90
Manufacturer:
MXIC
Quantity:
1 831
TABLE 7. SILICON ID CODE
READING ARRAY DATA
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. After
completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See Erase Suspend/Erase
Resume Commands” for more information on this mode.
The system
able the device for reading array data if Q5 goes high, or
while in the autoselect mode. See the "Reset Command"
section, next.
P/N:PM0709
Pins
Manufacture code
Device code
for MX29LV800(A)T Byte
Device code
for MX29LV800(A)B Byte
Sector Protection
Verification
must
issue the reset command to re-en-
Word VIL
Byte
Word VIH
Word VIH
Word X
Byte X
MX29LV800T/B & MX29LV800AT/AB
A0
VIL
VIH
VIH
A1
VIL
VIL
VIL
VIL
VIL
VIL
VIH X
VIH X
Q15~Q8 Q7 Q6 Q5
X
22H
X
22H
X
00H
1
1
1
1
0
0
0
0
14
1
1
1
1
1
1
0
0
RESET COMMAND
Writing the reset command to the device resets the
device to reading array data. Address bits are don't care
for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in a program command sequence before
programming begins. This resets the device to reading
array data (also applies to programming in Erase
Suspend mode). Once programming begins, however,
the device ignores reset commands until the operation
is complete.
The reset command may be written between the se-
quence cycles in an SILICON ID READ command
sequence. Once in the SILICON ID READ mode, the
reset command
data (also applies to SILICON ID READ during Erase
Suspend).
If Q5 goes high during a program or erase operation,
writing the reset command returns the device to read-
ing array data (also applies during Erase Suspend).
0
0
0
0
0
0
0
0
Q4 Q3 Q2 Q1 Q0 Code (Hex)
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
must
0
0
0
0
0
0
0
0
be written to return to reading array
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
0
00C2H
C2H
22DAH
DAH
225BH
5BH
01H (Protected)
00H (Unprotected)
REV. 2.5, DEC. 23, 2003

Related parts for MX29LV800AB