IMP706 IMP Inc, IMP706 Datasheet - Page 5

• Manufacturer Part Number: IMP706
• Description: LOW-POWER P SUPERVISOR CIRCUITS
• Manufacturer: IMP Inc

RESET/RESET Operation
The RESET/RESET signals are designed to start a µP/µC in a
known state or return the system to a known state.
The IMP707/708 have two RESET outputs, one active-HIGH
RESET and one active-LOW RESET output. The IMP813L has
only an active-HIGH output. RESET is simply the complement
of RESET.
RESET is guaranteed to be LOW with V
power-up sequence, RESET remains low until the supply rises
above the threshold level, either 4.65V, 4.40V or 4.00V. . RESET goes
high approximately 200ms after crossing the threshold.
During power-down, RESET goes LOW as V
threshold level and is guaranteed to be under 0.4V with V
above 1.2V.
In a brownout situation where V
level, RESET pulses low. If a brownout occurs during an already-
initiated reset, the pulse will continue for a minimum of 140ms.
Auxiliary Comparator
All devices have an auxiliary comparator with 1.25V trip point
and uncommitted output (PFO) and noninverting input (PFI).
This comparator can be used as a supply voltage monitor with an
external resistor voltage divider. The attenuated voltage at PFI
should be set just below the 1.25 threshold. As the supply level
falls, PFI is reduced causing the PFO output to transit LOW.
Normally PFO interrupts the processor so the system can be shut
down in a controlled manner.
RESET
©
WDO
1999 IMP, Inc.
V
MR
CC
5V
0V
5V
0V
5V
0V
5V
0V
Figure 1. WDI Three-state operation
v
RT
MR extermally
set low
t
RS
CC
t
MD
falls below the threshold
CC
above 1.2V. During a
CC
t
MR
falls below the
t
RS
408-432-9100/www.impweb.com
705_04.eps
CC
IMP813L
(RESET)
Manual Reset (MR)
The active-LOW manual reset input is pulled high by a 250µA
pull-up current and can be driven low by CMOS/TTL logic or a
mechanical switch to ground. An external debounce circuit is
unnecessary since the 140ms minimum reset time will debounce
mechanical pushbutton switches.
By connecting the watchdog output (WDO) and MR, a watchdog
timeout forces RESET to be generated. The IMP813L should be
used when an active-HIGH RESET is required.
Watchdog Timer
The watchdog timer available on the IMP705/706/813L monitors
µP/µC activity. If activity is not detected within 1.6 seconds, the
internal timer puts the watchdog output, WDO, into a LOW
state. WDO will remain LOW until activity is detected at WDI.
The watchdog function is disabled, meaning it is cleared and not
counting, if WDI is floated or connected to a three-stated circuit.
The watchdog timer is also disabled if RESET is asserted. When
RESET becomes inactive and the WDI input sees a high or low
transition as short as 50ns, the watchdog timer will begin a 1.6
second countdown. Additional transitions at WDI will reset the
watchdog timer and initiate a new countdown sequence.
WDO will also become LOW and remain so, whenever the
supply voltage, V
goes HIGH as soon as V
is no minimum pulse width for WDO as there is for the RESET
outputs. If WDI is floated, WDO essentially acts as a low-power
output indicator.
RESET
WDO
WDI
5V
0V
5V
0V
5V
0V
5V
0V
t
WP
CC
Figure 2. Watchdog Timing
, falls below the device threshold level. WDO
IMP705/6/7/8, 8
IMP705/6/7/8, 8
CC
t
WD
transitions above the threshold. There
RESET triggered by MR
Detail Descriptions
t
t
RS
WD
1
1
3L
3L
t
WD
705_05.eps
5