ADS8320E Burr-Brown Corporation, ADS8320E Datasheet - Page 12

• Manufacturer Part Number: ADS8320E
• Description: 16-Bit/ High-Speed/ 2.7V to 5V microPower Sampling ANALOG-TO-DIGITAL CONVERTER
• Manufacturer: Burr-Brown Corporation

FIGURE 6. Scaling f
FIGURE 5. Maintaining f
FIGURE 7. Shutdown Current with CS HIGH is 50nA
0.250
1000
0.00
1000
1000
800
600
400
200
100
0.0
100
10
10
1
1
0.1
0.1
0.1
T
V
V
f
CLK
T
f
A
CC
REF
Allows Supply Current to Drop Linearly with
Sample Rate.
CLK
A
Slightly with Sample Rate.
= 25 C
®
Typically, Regardless of the Clock. Shutdown
Current with CS LOW Varies with Sample
Rate.
= 25 C
= 5.0V
= 24 • f
= 5.0V
= 2.4MHz
ADS8320
SAMPLE
V
V
CC
REF
CLK
1
= 5.0V
1
1
Sample Rate (kHz)
= 5.0V
Sample Rate (kHz)
Sample Rate (kHz)
CLK
Reduces Supply Current Only
at the Highest Possible Rate
CS LOW (GND)
10
CS HIGH (V
10
10
T
V
V
f
CLK
A
CC
REF
= 25 C
= 5.0V
= 24 • f
V
V
= 5.0V
CC
REF
= 2.7V
= 2.5V
CC
SAMPLE
)
100
100
100
12
Figure 5 shows the current consumption of the ADS8320
versus sample rate. For this graph, the converter is clocked
at 2.4MHz regardless of the sample rate—CS is HIGH for
the remaining sample period. Figure 6 also shows current
consumption versus sample rate. However, in this case, the
DCLOCK period is 1/24th of the sample period—CS is
HIGH for one DCLOCK cycle out of every 16.
There is an important distinction between the power-down
mode that is entered after a conversion is complete and the
full power-down mode which is enabled when CS is HIGH.
CS LOW will shut down only the analog section. The digital
section is completely shutdown only when CS is HIGH.
Thus, if CS is left LOW at the end of a conversion and the
converter is continually clocked, the power consumption
will not be as low as when CS is HIGH. See Figure 7 for
more information.
Power dissipation can also be reduced by lowering the
power supply voltage and the reference voltage. The
ADS8320 will operate over a V
However, at voltages below 2.7V, the converter will not run
at a 100kHz sample rate. See the typical performance curves
for more information regarding power supply voltage and
maximum sample rate.
SHORT CYCLING
Another way of saving power is to utilize the CS signal to
short cycle the conversion. Because the ADS8320 places the
latest data bit on the D
converter can easily be short cycled. This term means that
the conversion can be terminated at any time. For example,
if only 14 bits of the conversion result are needed, then the
conversion can be terminated (by pulling CS HIGH) after
the 14th bit has been clocked out.
This technique can be used to lower the power dissipation
(or to increase the conversion rate) in those applications
where an analog signal is being monitored until some con-
dition becomes true. For example, if the signal is outside a
predetermined range, the full 16-bit conversion result may
not be needed. If so, the conversion can be terminated after
the first n bits, where n might be as low as 3 or 4. This results
in lower power dissipation in both the converter and the rest
of the system, as they spend more time in the power-down
mode.
LAYOUT
For optimum performance, care should be taken with the
physical layout of the ADS8320 circuitry. This will be
particularly true if the reference voltage is low and/or the
conversion rate is high. At a 100kHz conversion rate, the
ADS8320 makes a bit decision every 416ns. That is, for each
subsequent bit decision, the digital output must be updated
with the results of the last bit decision, the capacitor array
appropriately switched and charged, and the input to the
comparator settled to a 16-bit level all within one clock
cycle.
OUT
line as it is generated, the
CC
range of 2.0V to 5.25V.