ATxmega192A3U Atmel Corporation, ATxmega192A3U Datasheet - Page 9

• Manufacturer Part Number: ATxmega192A3U
• Manufacturer: Atmel Corporation

Specifications of ATxmega192A3U

• Flash (kbytes): 192 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 50
• Ext Interrupts: 50
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 10
• Twi (i2c): 2
• Uart: 7
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 16
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 7
• Output Compare Channels: 22
• Input Capture Channels: 22
• Pwm Channels: 22
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

3.7
3.8
8331A–AVR–07/11
Status Register
Stack and Stack Pointer
Figure 3-3 on page 9
cycle, an ALU operation using two register operands is executed and the result is stored back to
the destination register.
Figure 3-3.
The status register (SREG) contains information about the result of the most recently executed
arithmetic or logic instruction. This information can be used for altering program flow in order to
perform conditional operations. Note that the status register is updated after all ALU operations,
as specified in the instruction set reference. This will in many cases remove the need for using
the dedicated compare instructions, resulting in faster and more compact code.
The status register is not automatically stored when entering an interrupt routine nor restored
when returning from an interrupt. This must be handled by software.
The status register is accessible in the I/O memory space.
The stack is used for storing return addresses after interrupts and subroutine calls. It can also be
used for storing temporary data. The stack pointer (SP) register always points to the top of the
stack. It is implemented as two 8-bit registers that are accessible in the I/O memory space. Data
are pushed and popped from the stack using the PUSH and POP instructions. The stack grows
from a higher memory location to a lower memory location. This implies that pushing data onto
the stack decreases the SP, and popping data off the stack increases the SP. The SP is auto-
matically loaded after reset, and the initial value is the highest address of the internal SRAM. If
the SP is changed, it must be set to point above address 0x2000, and it must be defined before
any subroutine calls are executed or before interrupts are enabled.
During interrupts or subroutine calls, the return address is automatically pushed on the stack.
The return address can be two or three bytes, depending on program memory size of the device.
For devices with 128KB or less of program memory, the return address is two bytes, and hence
the stack pointer is decremented/incremented by two. For devices with more than 128KB of pro-
gram memory, the return address is three bytes, and hence the SP is decremented/incremented
by three. The return address is popped off the stack when returning from interrupts using the
RETI instruction, and from subroutine calls using the RET instruction.
Register Operands Fetch
ALU Operation Execute
Total Execution Time
Result Write Back
Single Cycle ALU Operation
shows the internal timing concept for the register file. In a single clock
clk
CPU
T1
Atmel AVR XMEGA AU
T2
T3
T4
9