AT86RF231 Atmel Corporation, AT86RF231 Datasheet - Page 86
AT86RF231
Manufacturer Part Number
AT86RF231
Description
Manufacturer
Atmel Corporation
Datasheet
1.AT86RF231.pdf
(198 pages)
Specifications of AT86RF231
Max. Operating Frequency
0 MHz
Crypto Engine
AES
Operating Voltage (vcc)
1.8 to 3.6
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
2
Antenna Diversity
Yes
External Pa Control
Yes
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
13.2
Transmit Current Consumption (ma)
14.4
Link Budget (dbm)
104
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT86RF231-ZU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
- Current page: 86 of 198
- Download datasheet (5Mb)
8.2.3
8.2.4
8111C–MCU Wireless–09/09
Automatic FCS generation
Automatic FCS check
The automatic FCS generation is performed with register bit TX_AUTO_CRC_ON = 1 (reset
value). This allows the AT86RF231 to compute the FCS autonomously. For a frame with a frame
length specified as N (3 ≤ N ≤ 127), the FCS is calculated on the first N-2 octets in the Frame
Buffer, and the resulting FCS field is transmitted in place of the last two octets from the Frame
Buffer.
If the radio transceivers automatic FCS generation is enabled, the Frame Buffer write access
can be stopped right after MAC payload. There is no need to write FCS dummy bytes.
In RX_AACK mode, when a received frame needs to be acknowledged, the FCS of the ACK
frame is always automatically generated by the AT86RF231, independent of the
TX_AUTO_CRC_ON setting.
Example:
A frame transmission of length five with TX_AUTO_CRC_ON set, is started with a Frame Buffer
write access of five bytes (the last two bytes can be omitted). The first three bytes are used for
FCS generation; the last two bytes are replaced by the internally calculated FCS.
An automatic FCS check is applied on each received frame with a frame length N
bit RX_CRC_VALID (register 0x06, PHY_RSSI) is set if the FCS of a received frame is valid.
The register bit is updated when issuing interrupt IRQ_3 (TRX_END) and remains valid until the
next TRX_END interrupt caused by a new frame reception.
In RX_AACK mode, if FCS of the received frame is not valid, the radio transceiver rejects the
frame and the TRX_END interrupt is not issued.
In TX_ARET mode, the FCS and the sequence number of an ACK is automatically checked. If
one of these is not correct, the ACK is not accepted.
AT86RF231
2. Register
86
Related parts for AT86RF231
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: