AT83EB5114 Atmel Corporation, AT83EB5114 Datasheet - Page 56
AT83EB5114
Manufacturer Part Number
AT83EB5114
Description
Manufacturer
Atmel Corporation
Datasheet
1.AT83EB5114.pdf
(95 pages)
Specifications of AT83EB5114
Max. Operating Frequency
24 MHz
Cpu
8051-12C
Max I/o Pins
11
Adc Channels
6
Adc Resolution (bits)
10
Adc Speed (ksps)
50
Sram (kbytes)
0.25
Eeprom (bytes)
256
Operating Voltage (vcc)
3.0 to 3.6
Timers
4
Mask Rom (kbytes)
4
Watchdog
Yes
- Current page: 56 of 95
- Download datasheet (942Kb)
WatchDog Timer During
Power Down Mode and
Idle
56
AT89/83EB5114
Find Hereafter computed Time-Out value for Fosc = 12 MHz
Table 42. Time-Out Computation @12 MHz
Table 43. WDTRST Register
Reset Value = XXXX XXXXb
The WDTRST register is used to reset/enable the WDT by writing 1EH then E1H in
sequence.
In Power Down mode the oscillator stops, which means the WDT also stops. While in
Power Down mode the user does not need to service the WDT. There are 2 methods of
exiting Power Down mode: by a hardware reset or via a level activated external interrupt
which is enabled prior to entering Power Down mode. When Power Down is exited with
hardware reset, servicing the WDT should occur as it normally does whenever
AT8xEB5114 is reset. Exiting Power Down with an interrupt is significantly different. The
interrupt is held low long enough for the oscillator to stabilize. When the interrupt is
brought high, the interrupt is serviced. To prevent the WDT from resetting the device
while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high.
It is suggested that the WDT be reset during the interrupt service for the interrupt used
to exit Power Down.
To ensure that the WDT does not overflow within a few states of exiting of power down,
it is best to reset the WDT just before entering power down.
In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting
while in Idle mode, the user should always set up a timer that will periodically exit Idle,
service the WDT, and re-enter Idle mode.
7
-
S2
0
0
0
0
1
1
1
1
6
-
S1
0
0
1
1
0
0
1
1
5
-
S0
0
1
0
1
0
1
0
1
4
-
3
-
Time-Out for F
2
-
131.07 ms
262.14 ms
524.29 ms
16.38 ms
32.77 ms
65.54 ms
1.05 s
2.10 s
OSC
=12 MHz
1
-
4311C–8051–02/08
0
-
Related parts for AT83EB5114
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: