SC16IS750IPW-T NXP Semiconductors, SC16IS750IPW-T Datasheet - Page 12

• Manufacturer Part Number: SC16IS750IPW-T
• Description: IC UART I2C/SPI 24-TSSOP
• Manufacturer: NXP Semiconductors

Specifications of SC16IS750IPW-T

• Features: Low Current
• Number Of Channels: 1, UART
• Fifo's: 64 Byte
• Protocol: RS232, RS485
• Voltage - Supply: 2.5V, 3.3V, 5V
• With Auto Flow Control: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP (0.173", 4.40mm Width)
• For Use With: 568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NXP Semiconductors
SC16IS740_750_760_6
Product data sheet
7.3.1 RX
7.3.2 TX
There are two other enhanced features relating to software flow control:
When software flow control operation is enabled, the SC16IS740/750/760 will compare
incoming data with Xoff1/Xoff2 programmed characters (in certain cases, Xoff1 and Xoff2
must be received sequentially). When the correct Xoff characters are received,
transmission is halted after completing transmission of the current character. Xoff
detection also sets IIR[4] (if enabled via IER[5]) and causes IRQ to go LOW.
To resume transmission, an Xon1/Xon2 character must be received (in certain cases
Xon1 and Xon2 must be received sequentially). When the correct Xon characters are
received, IIR[4] is cleared, and the Xoff interrupt disappears.
Xoff1/Xoff2 character is transmitted when the RX FIFO has passed the HALT trigger level
programmed in TCR[3:0] or the selectable trigger level in FCR[7:6]
Xon1/Xoff2 character is transmitted when the RX FIFO reaches the RESUME trigger level
programmed in TCR[7:4] or RX FIFO falls below the lower selectable trigger level in
FCR[7:6].
The transmission of Xoff/Xon(s) follows the exact same protocol as transmission of an
ordinary character from the FIFO. This means that even if the word length is set to be 5, 6,
or 7 bits, then the 5, 6, or 7 least significant bits of XOFF1/XOFF2 or XON1/XON2 will be
transmitted. (Note that the transmission of 5, 6, or 7 bits of a character is seldom done, but
this functionality is included to maintain compatibility with earlier designs.)
It is assumed that software flow control and hardware flow control will never be enabled
simultaneously.
•
•
Xon Any function (MCR[5]): Receiving any character will resume operation after
recognizing the Xoff character. It is possible that an Xon1 character is recognized as
an Xon Any character, which could cause an Xon2 character to be written to the RX
FIFO.
Special character (EFR[5]): Incoming data is compared to Xoff2. Detection of the
special character sets the Xoff interrupt (IIR[4]) but does not halt transmission. The
Xoff interrupt is cleared by a read of the IIR. The special character is transferred to the
RX FIFO.
Figure 11
Single UART with I
Rev. 06 — 13 May 2008
shows an example of software flow control.
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
SC16IS740/750/760
© NXP B.V. 2008. All rights reserved.
12 of 62